Ask Experts Questions for FREE Help !
Ask
    The Ants Go Marching's Avatar
    The Ants Go Marching Posts: 1, Reputation: 1
    New Member
     
    #1

    Dec 22, 2007, 01:27 PM
    How old is my Furnasman Furnace? HG 100-27
    How old is my "Air Conditioning" Furnasman Furnace? Model HG 100-27. The house was built in 1953, and this old aqua coloured baby looks very simple. I know it will need replacing at some point, but it keeps working. The utility company sent out a flyer saying heating costs typically account for up to 60% of household energy costs. My heating accounts for 58% of my costs. I use a programmable thermostat, so that helps. I can think of lots of things I need to spend money on (Replacing the leaking double glazed windows, and the fireplace dampers that are bent and don't seal off the heat loss)- should I really make replacing the old beast a priority?
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
     
    #2

    Dec 22, 2007, 03:36 PM
    Yes you should. The newer 95 to 98 % units really do save big bucks especially when you are replacing a 55 to 62% efficient older equipment.

    Windows and fireplace dampers are also very important but you can caulk and use plastic inside storm windows for that and the dampers can be picked up at any brick supply yard. Just take your old damper out to find a replacement.
    T-Top's Avatar
    T-Top Posts: 1,871, Reputation: 100
    Ultra Member
     
    #3

    Dec 22, 2007, 05:47 PM
    I agree with hvac1000. Look at it this way if you commuted to work 80 miles a day in a car that got 6 miles to the gallon would you buy a newer car that got 20 miles to the gallon to help save money. Buying the new unit will cost some money on the front end but it will pay for its self and save you money in the long run.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Wiring a furnace thermostat to manually operate the furnace fan [ 2 Answers ]

I have two wires connected to my furnace thermostat. There is a place labeled G on the thermostat. Can I simply run a wire from the G terminal on my thermostat to the terminal labeled G on my furnace fan relay to operate the fan separately?

York Stellar Furnace Heating up Furnace Room to 110 Degress? [ 2 Answers ]

I have a York Stellar Furnace in my newly purchased house. Furnace is 15 years old. Furnace is releasing hot air from front grills and heats up furnace room to 110 Degrees. I had a Bryant Furnace in another house and this never happened. All plenams and ducts are taped and sealed so the heat is...

Goodman furnace GMNT080-4 furnace runs good for a while then has to be manually reset [ 5 Answers ]

I have a Goodman GMNT080-4 (90%). I'm having the same problem As Streatherg did back in the Nov 2006 question. I reviewed his article and tried Every thing on there but seems to be doing the same thing. The furnace kicks on for about an hour then locks out and has to be manually reset threw...

Gas furnace pilot trouble. Goes out while furnace is running! [ 1 Answers ]

About a month ago I put in a new thermocoupler in my furnce and it's been working fine. This morning I woke up to no heat. I can re-light the pilot with no problems. The piot light keeps on burning if I don't turn the thermostat up to turn on the furnace. Then when I set the thermostat to 70...

Comfortmaker Furnace Fan blows in line fuse and will not allow furnace to work [ 1 Answers ]

I have a Comfortmaker Furnace (approximately 1998/99) and the fan will not turn on allow the furnace to heat. When I try to turn the furnace on it blows a 3 amp fuse at the blower motor. I removed the fuse and jumped it and all it will do is make a faint buzzing noise and not turn on. I can...


View more questions Search