Ask Experts Questions for FREE Help !
Ask
    jsjones01's Avatar
    jsjones01 Posts: 18, Reputation: 1
    New Member
    		  
    #1

    Dec 5, 2007, 02:58 PM
    Changing ducting on Wesco electric furnace
    I just found this site! Hopefully someone can guide me. I just bought a small old house - 1 story. It has a Wesco electric furnace, mfg date 12/27/1980. There are cold air return ducts in every room except bath, located at the bottom of the walls near the floor. The heat vents are located in the ceilings of each room. I want to raise the ceilings in kitchen, 2 bdrms, and LR/DR as the ceilings are very low. Can I change existing ducts to have hot air travel through the existing cold air duct system, and use a couple of existing hot air ducts to supply the cold air return? In essence, I want to reverse the function of existing ducts: hot would become cold, cold would be hot (with new insulation). Is this possible? Thanks!
    JJ
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
    		  
    #2

    Dec 6, 2007, 09:06 AM
    Anything is possible but the expence will be great. The duct size is probably be wrong when you change the function for the ducts.
    jsjones01's Avatar
    jsjones01 Posts: 18, Reputation: 1
    New Member
    		  
    #3

    Dec 6, 2007, 11:31 AM
    Quote Originally Posted by hvac1000
    Anything is possible but the expence will be great. The duct size is probably be wrong when you change the function for the ducts.
    Since I'm going to raise the ceilings I will have to reroute the existing hot air ducts to someplace other than the ceilings. Do you think rerouting the existing air ducts will be cheaper than than reversing the function of the existing ducts (and whatever it takes to do that)? Why are the ducts different sizes? Thanks
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
    		  
    #4

    Dec 6, 2007, 11:42 AM
    Reroute will be cheaper. Return and supply diuct are engineered differently for air flow and capacity. You might check with a local HVAC company to get a bid and ask them what would be best for you under your circumstances. It does not mean you have to buy from them but the job could be over your head as far as engineering/sizing/flow rate/ etc. Your furnace is also getting old. You might consider a heat pump to decrease your utility bills.
    jsjones01's Avatar
    jsjones01 Posts: 18, Reputation: 1
    New Member
    		  
    #5

    Dec 7, 2007, 12:06 AM
    Do I need to find a local HVAC company that carries my brand of furnace to give me a quote? Or can I go to any HVAC company? If I decide to get a new furnace/heat pump, can my existing ductwork be used or do I have to pay to rip it all out and start over? This sounds ridiculous, but can I run the furnace upside down and have it blow hot air down through the existing (insulated) cold air ducts and use the existing hot air ducts in the ceiling as my cold air returns? OR if the cold air return ducts need to be larger than the hot ducts, I could just upsize the ceiling ducts. I am an engineer, so is there a formula I can use to figure out all sizing/flowrate, etc? I just don't know the science behind forced air furnace efficiency. You have been very helpful - thanks!
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
    		  
    #6

    Dec 7, 2007, 12:14 AM
    ((can I go to any HVAC company))
    Yes you can and I suggest you pose your questions to them since they will be the ones seeing your system and what can be done with it.
    jsjones01's Avatar
    jsjones01 Posts: 18, Reputation: 1
    New Member
    		  
    #7

    Dec 7, 2007, 12:27 AM
    I will call a local HVAC company and ask their thoughts. Thanks for you're your insights. I appreciate the guidance.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Propable changing electric wires [ 3 Answers ]

Hi I brought a chandelier from Europe to usa & after connecting it to electricity , we found that its light is very very weak!! The handy man said may be you need to change its 220 volt thin wires to thick 110 volt wires ? Could you please advice me how to solve this & which kind of shop deals...

Changing gas to electric [ 5 Answers ]

I am thinking of buying a home. The one I want uses gas for heating and cooking. How hard would it be to convert that to electric? I am terrified of blowing myself up in a home that has gas. The house I am looking at is about a 100 years old. Any information would be great.

Changing light switches and now electric plugs don't work [ 2 Answers ]

I am trying to change the light switches in my apartment. I found out after taking out the old switch, that there is no ground but there were 3 separate black wires coming from the box. I changed the old to the new switch, but since there were 3 black cables coming out, I only back mounted 2 of the...

WESCO UEM,allways on now [ 1 Answers ]

I have a WESCO uem 20kw electric furnace, about 25 yrs old, It had a single temp stat first then a setback stat was installed, with a box added to the furnace controls, the set back stat failed after a few years so I put the original single temp stat back and it worked for years now, a while back...

Ducting [ 1 Answers ]

My old ducting is worn out and has several leaks in it and it is hard to get to. Is there a flexible type duct that I can pull threw the old duct work and make new connections at all the registers for a better air flow.

View more questions Search