Ask Experts Questions for FREE Help !
Ask
    tx2931's Avatar
    tx2931 Posts: 5, Reputation: 1
    New Member
     
    #1

    Nov 23, 2005, 06:10 AM
    Boiler issues
    I have a water boiler with an external pump and an internal transformer as my heating source, controlled by a Honeywell programmable thermostat. The PROBLEM: #1. When I turn on my heat, the PUMP will NOT START sometimes! At times, it WILL START and run! Sometimes it will start but cycle off after 10-15 minutes! When it doesn't start or cycles off, the only way to start the pump is to turn ON and OFF (sometimes repeatedly) the MAIN power switch to the system! Problem #2. I have replaced my TRANSFORMER TWICE because they melted (the plastic where the terminal screws are). I thought maybe the internal heat was the problem so I leave the door ajar to allow heat to escape! This is my second winter with this transformer and seems to be holding up with just a small amount of melting! Thanks AL
    labman's Avatar
    labman Posts: 10,580, Reputation: 551
    Uber Member
     
    #2

    Nov 23, 2005, 07:46 AM
    The pump is controlled by a relay. I don't know if it has a delay like forced air, but the intermittent problem likely is the relay. You may want to look at the transformer. It is possible it is not big enough to handle the gas valve, the pump relay, the ignition, any zone valves, anything else the system needs to start up. If the inadequate transformer isn't putting out a full 24 volts, that could cause the relay problems too. If you have a volt meter, the first thing I would do is check the voltage at the transformer when the system kicks on. If it drops below 24 volts more than momentarily, either the transformer is too small, or something is drawing too much current. You could add up everything connected on start up and compare it to the rating of the transformer. The devices should all be marked with an amperage or watts. Multiply the amps by 24 volts to convert to watts. If the total is as much or more than the transformer, replace it with a bigger one. If less, try to check each device for excessive current. Heating up is a sure clue.

    I would also add a fuse for the transformer. They are cheaper to replace than transformers.
    tx2931's Avatar
    tx2931 Posts: 5, Reputation: 1
    New Member
     
    #3

    Nov 29, 2005, 11:34 AM
    Boiler issues
    Thanks for the info. I will try your suggestions. I'm going to try attaching some pictures of system!

    AL

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Boiler question [ 10 Answers ]

I live in the state of NY. Does anyone know if it is code to have a low level cutoff when installing a boiler? I am not sure exactly what that is or where it would be installed but I wanted to make sure. I had an estimate by a company and they don't seem like they are going to do this unless I want...

Boiler keeps fusing [ 3 Answers ]

I have a combi boiler which has been going great it cut out yesterday and then the digital display and power went off. I spotted the blown fuse which I have replaced but it keeps fusing any ideas?

Boiler wiring [ 19 Answers ]

Ok, I will try to explain this the best I can with what I saw. I have an old repco boiler with 2 zones and I was wondering if the wiring was correct. The 2 zones are wired into a master control box then goes out to the pump on the boiler and the 2 thermos and another set of wires to another box(not...

Boiler replacement [ 3 Answers ]

I live in Chicago in a 2300 sq ft ranch. The home was built in 1955, and has the original boiler, which was converted from oil to natural gas. Although the boiler is working fine, I wonder about replacing it as the cost of natural gas keeps going up. The efficiency of the new boilers must be far...


View more questions Search