 |
|
|
 |
New Member
|
|
Nov 12, 2007, 08:45 AM
|
|
Shut off valve isn''t working
I bought a toilet tank for replacement purposes. The shut off valve is not shutting off the
Entire water flow to my tank. I can see & hear hear water entering the tank. I tried hand tightening the shut off valve but dare to go further for fear of damaging the connection. I am afraid if I disconnect the supply line my bathroom floor will be flooded.
|
|
 |
Home Repair & Remodeling Expert
|
|
Nov 12, 2007, 08:55 AM
|
|
If the stop cock under the tank is not closing all the way you will need to shut down your main and open a fuacet to blow off pressure. Your shut off valve may be a 1/4 turn variety or it may take several turns. They are not hard to replace or expensive, about $6. Can't be more specific since I don't know if the stop is threaded onto a supply line or soldered but in any case you should replace the stop cock. If it is threaded be sure to apply 3 full wraps of white teflon tape to the pipe thread, if soldered remember to disassemble the valve and remove the stem before soldering.
|
|
 |
Uber Member
|
|
Nov 12, 2007, 02:36 PM
|
|
You can add a retrofit 1/4 turn valve on top of the valve that you have. It can avoid unpleasantries of replacing the permanent one. Some are extremely difficult.
|
|
 |
Home Repair & Remodeling Expert
|
|
Nov 12, 2007, 04:10 PM
|
|
KISS are you thinking of something like a stop cock that is compression on both ends? That would work and the dribble on the floor during the install won't be too bad. It sure will look like hell but who looks at angle stop cocks anyway.
|
|
 |
Uber Member
|
|
Nov 12, 2007, 07:25 PM
|
|
Nope. I'm thinking of one of these things. It's a whole lot easier to turn the toilet off with a 1/4 turn than to turn, turn, turn etc. especially when there is a problem. It's well worth it.
The angle stop is soldered and a real pain to replace.
Any idea what to do with the rusty eustacheon.
|
|
 |
Home Repair & Remodeling Expert
|
|
Nov 13, 2007, 08:50 AM
|
|
Yep, cut it off with aviation tin snips and then buy one that is two pieces with a hinge that allows you to wrap around the pipe. I have seen some plastic one with a chrome finish that have a split and can be wrapped. Your pic is pretty much what I pictured just not compression on both ends. Nice tile, when are we going to rip it out? Just Kidding.
Bob
|
|
Question Tools |
Search this Question |
|
|
Add your answer here.
Check out some similar questions!
Shut off valve not working!
[ 34 Answers ]
Hi:
I am trying to fix a leaky compression faucet. I have turned off the shut off valve for the cold water under the sink so the when the handle for the cold water of the compression faucet is turned, there is no water as expected.
However, even if I turn off the shut off valve for the hot...
Shut off valve
[ 3 Answers ]
I just installed a new plastic shut off valve to my hot water supply on my lavatory and I cannot get it to open. I am thinking that the glue may have glued it closed. Any ideas on how to get it unstuck without replacing it?
Where's toilet shut off valve?
[ 1 Answers ]
I cannot find a valve to shut off my constantly running toilet, till the plumber can arrive. Every other place I've lived has had a separate shutoff valve for each toilet, sink, etc. I've looked in, under & around the back of the tank, but there is no valve on the pipe in the bathroom. I've also...
Water Shut-off Valve
[ 1 Answers ]
I am attempting to replace the valve supplying water to the toilet water tank, but am unable to unscrew it. It turns, but it does not come off. What can I do? Need help ASAP! Thank you!
View more questions
Search
|