Ask Experts Questions for FREE Help !
Ask
    bruceedward's Avatar
    bruceedward Posts: 3, Reputation: 1
    New Member
    		  
    #1

    Oct 31, 2007, 07:23 AM
    Bathroom fan wiring
    I am finishing a basement 3/4 bath. I have run a separate 20 amp (12g) circuit from panel to GFI outlet in bathroom. From that I want to run to bathroom fan.

    Can I run to fan and then to switch for the fan or do I HAVE to run the wire to the switch and then the fan - I have been told I must go to the switch first from a GFI... I don't understand why this would be true.

    I want to run the wire from the GFI because that is on 12 gauge wire and that is the only 12 gauge/20 amp circuit in the bath. I have not purchased the fan yet but want to be prepared assuming it calls for 20 amp.

    Please help.
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
    		  
    #2

    Oct 31, 2007, 07:31 AM
    Unless Manufacturer reccomends, Usually you don't.
    I would run power to switch location, then to 3 locations(the GFI, The Light, and the fan)
    RustyFairmount's Avatar
    RustyFairmount Posts: 165, Reputation: 40
    Junior Member
    		  
    #3

    Oct 31, 2007, 08:52 PM
    In order to get the maximum benefit from the GFI, you MUST run the power to the GFI first, then to the switches, and from there to the fan, lights, etc. That way, the lights, fan, switch, and GFI will all be protected from a ground fault. Otherwise, only the GFI itself will be protected.

    Carefully read the installation instructions that came with the GFI. It should explain why.
    tkrussell's Avatar
    tkrussell Posts: 9,659, Reputation: 725
    Uber Member
    		  
    #4

    Nov 1, 2007, 02:46 AM
    I don't see any need for GFI protection of the bathroom light and exhaust fan, unless either are directly over the tub or shower enclosure. If the GFI trips, the bathroom will be dark.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Wiring inline duct fan to furnace fan goodman gmp100-4 [ 2 Answers ]

How do I wire my inline duct fan to my Goodman model gmp100-4 gas furnace fan so that the inline duct fan comes on and off when the furnace fan does? I understand that I need a relay from the inline duct fan but don't know where to connect the relay to the furnace.

Bathroom Exhaust Fan Wiring [ 2 Answers ]

I'm trying to wire an exhaust fan to an bathroom light switch; how do I go about doing this project. The existing light switch is a single pole, and I assume I will need to install another double box for two (2) switches - one for the existing light and the other for the NEW exhaust fan. ...

Bathroom Wiring [ 1 Answers ]

I have read as many bathroom posts as I could find but still have a specific question. First I want to reiterate what I have gathered. Please verify the following for correctness. 1. Outlets and lights must be on separate circuits in a bathroom. 2. All outlets must be GFI protected by breaker...

Need help wiring a bathroom? [ 6 Answers ]

I am installing a new bathroom in my basement and have a few questions. First a little information on the circuits. The bathroom will have 2 circuits. Circuit-1 = (2) GFCI's one on each side of vanity top. No lights, switches or appliances on this circuit. Circuit is dedicated only to the...

Bathroom light + extractor fan wiring [ 1 Answers ]

I am about to replace the light fitting in the bathroom, but the extractor fan is connected to it, there is a number of wires which are all connected, with only 2 brown wires coming down, but I have 3 connections on my new light fitting -earth, live, neutral, how do I connect it properly?...

View more questions Search