Ask Experts Questions for FREE Help !
Ask
    roseport2000's Avatar
    roseport2000 Posts: 3, Reputation: 1
    New Member
     
    #1

    Oct 26, 2007, 09:48 PM
    Pressure swith, well system
    The points on the pressure switch "stick together" and then the pump will not run. This is happening quite frequently. It all started after we had been gone from the house for some time. Now, I was in the shower and noticed the pressure reducing & my hubby went out and tapped on the pressure switch and it "kicked on". What is making the points stick together? :confused: Is there anything I can do to make the points Not Stick together? Can I spray with something like WD40?
    I really hope someone can help me with this problem. We have lived here for 10 years and this is always a problem. This pump is inside the garage so it is not exposed to weather. We live in Florida. This is the 2nd pump in the system. We added a aeration tank outside and it has a pump also. It seems there is always some problem with a pump.
    TIA for your help.
    Rose
    [email protected]
    withoutwheels's Avatar
    withoutwheels Posts: 1, Reputation: 1
    New Member
     
    #2

    Oct 26, 2007, 10:29 PM
    It is time to replace the worn out pressure switch, about 20 bucks at menards. Either they are sticking open or if stuck together they are not making good contact.
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
     
    #3

    Oct 27, 2007, 04:41 AM
    You may clean and dress the contacts but the best advice is what Wheels gave you. Simply replace the pressure switch. Good luck, Tom
    roseport2000's Avatar
    roseport2000 Posts: 3, Reputation: 1
    New Member
     
    #4

    Oct 27, 2007, 08:21 AM
    I have only had this pump for about 2 years and it sits inside the garage so it is not out in the weather. Why has the switch worn out so quickly? Is this normal? Growing up we had a well system and I don't remember this problem ( & my dad made us help him with all his projects)! Oh well, $20 is no problem for peace of mind. Just curious, I'm too curious. THANK YOU ALL for your help! :D Rose

    Quote Originally Posted by withoutwheels
    It is time to replace the worn out pressure switch, about 20 bucks at menards. Either they are sticking open or if stuck together they are not making good contact.
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
     
    #5

    Oct 27, 2007, 09:07 AM
    Why has the switch worn out so quickly? Is this normal?
    Who knows why contacts arc and weld themselves together. Perhaps your pump motor's drawing more amps then it should putting the load back on the contacts every time they oipen and close. The point is it needs to be replaced. You might also check the pump motor to see how many amps it's pulling at start up. Good luck, Tom
    roseport2000's Avatar
    roseport2000 Posts: 3, Reputation: 1
    New Member
     
    #6

    Oct 27, 2007, 11:24 AM
    Thank you for your replies. Is it possible for you to "walk me thru" how to check the motor for the amp draw? I have a small multimeter although I really don't know how to use it.
    TIA Rose

    Quote Originally Posted by speedball1
    Who knows why contacts arc and weld themselves together. Perhaps your pump motor's drawing more amps then it should putting the load back on the contacts every time they oipen and close. The point is it needs to be replaced. You might also check the pump motor to see how many amps it's pulling at start up. good luck, Tom
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
     
    #7

    Oct 27, 2007, 02:34 PM
    I have a small multimeter although I really don't know how to use it.
    A multi meter won't get it You'll need a Amp-Probe for that. Mine handles any where from 6 amps to 300. Regards, Tom

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Increase water pressure with well system [ 1 Answers ]

I'm wanting to increase my water pressure in my house. I am on a well system with at controld device inline right after my pressure gauge and well tank with bladder. I saw an article that someone else ask about this, where you all gave instructions on increasing the water pressure by turning the...

System losing pressure [ 1 Answers ]

Twice in the last 2 weeks I have lost all water pressure on my system.On both occasions I have had to manually restart the pump.would this be a pump or pressure control failure?The system seems to run wel then all of a sudden no water.

Double swith [ 5 Answers ]

Can someone help I have a double swith that I am trying to connect, I have red,white black ground wires coming out the wall. And I have a green wire in the switch. Can someone give me direction how to connect them. Thanks

No pressure sprinkler system. [ 3 Answers ]

We recently had a sprinkler system installed. We have a well. According to the sprinkler guy, our lack of pressure is not his problem. Is there a way to boost the pressure in the system?

How do I increase H2O pressure on well system with a water filtration system? [ 2 Answers ]

Howdy, I would like to know how I can increase my water pressure. My current system uses a well pump with a small pressure tank, and "D" control valve. It then runs through a WATERSOFT filtration tank, RAINSOFT water softner, and on the Hot water side, an AQUASTAR on demand hot water system. I...


View more questions Search