Ask Experts Questions for FREE Help !
Ask
    SCNetworks's Avatar
    SCNetworks Posts: 2, Reputation: 1
    New Member
     
    #1

    Oct 25, 2005, 04:17 AM
    Finishing Basement - 8' or 9' Sheetrock?
    Am taking the plunge and finishing my basement, have just started. You may see me on this board with many questions to come...

    First is the size of drywall to buy. My ceiling is 9' tall to the joists with at least 1' of this holding pipes, electrical, duct work, etc. Have definitely decided on a drop ceiling. My neighbor recommended just getting 8' sheets to save money (the drop ceiling will cover the rest) - but in many places the sheetrock can easily go just about 9' to the top along the walls. I could use advice on what best to buy before I have 7500 lbs. of the stuff delivered. Am trying to do things right and purchase the paperless wallboard - so cost is a bit of an issue.

    Second question is the vapor barrier. If I do use 8' sheets and a drop ceiling, do I actually create an opening at the top for moisture to form and drop down the walls? Is there anything good to do to remedy / patch up this top part? Some insulation possibly? The walls will have a nice coat of drylock on them first against the concrete part - it's a daylight basement with about 1/2 poured foundation, the other 1/2 framed.

    Thank you in advance...
    labman's Avatar
    labman Posts: 10,580, Reputation: 551
    Uber Member
     
    #2

    Oct 25, 2005, 08:03 AM
    Moisture is going to be a big problem. Do you have good foundation drains? On my crawl space I put plastic sheeting over the Dry-Loc covered walls and the floor. I have also regraded, running water away from the house. The crawl space is meticulously sealed except for the vent for combustion air for my furnace. It stays dry year around. Go down there in the summer time, and the pipes don't have moisture condensed on them.

    I would put plastic over the outside walls, foam insulation all the way to the floor above, and go with the 8' drywall. Use your central A/C or a dehumidifier to keep warm, moist air out of the basement in the summer. Dry-Loc the floor too or something. Maybe it has a good sheet of plastic under it.
    SCNetworks's Avatar
    SCNetworks Posts: 2, Reputation: 1
    New Member
     
    #3

    Oct 25, 2005, 09:55 AM
    Thank you labman - here's the rest of my ideas on the basement so far, please let me know if a good alternative:

    - 8' Sheetrock as you say.
    - Drylock on poured concrete walls. 1/2" Polystyrofoam (Dow) sheets over that between the wall and framing, paperless wallboard on top of this. Was all I was going to do, but now maybe an extra sheet of plastic between frame and wallboard?
    - R19 paper faced out on 1/2 frammed section already (not below grade) - paperless wallboard on top of this.
    - Between top of sheetrock and joists - use plastic with foam insulation.
    - Some type of Drylock treatment for the floor (if any one has a good product to use / recommend please let me know).
    - If and when I can afford (will do first with bathroom) use "Dricore" (http://www.dricore.com) sections on top of painted floor. I do not have a basement drain internally - but think this will help.

    The footings for my basement actually sit about 15' below my poured slab - and this is where the drains actually sit. There is some grading externally that will help a bit - but all in all it's usually dry, although the dehumidifier does fill up twice a day during the summer. I'm located in HotLanta.

    Final touch is to tap into the furnace for two outlet / inlets for HVAC. This I think is most important.

    My winter project...
    labman's Avatar
    labman Posts: 10,580, Reputation: 551
    Uber Member
     
    #4

    Oct 25, 2005, 10:35 AM
    Mostly sounds good to me. I am not sure about the extra layer of plastic or the paper in. The great thing about foam insulation is that often the dew point is inside it, inaccessible to water vapor. Otherwise, vapor can collect on the cold side of a vapor barrier, and condense. Better to let it go.

    Do not be impressed by the Ultra expert after my name. Any idiot can be an ultra expert here by making enough posts and a few have. I am just a home owner who has worked out a few of his problems himself. I also have some industrial maintenance experience and am in charge of the maintenance of my church. The only area I really have much special knowledge is in dogs.

    We have some good people in plumbing, computers, and electrical; some areas I can't say, and some we are thin.
    gpjojo's Avatar
    gpjojo Posts: 1, Reputation: 1
    New Member
     
    #5

    Oct 25, 2011, 07:46 PM
    I am from the Texas gulf coast and never understood why people up north dig holes under their houses? My daughter lives in DC. I have a few suggestions. Use 2 1/2 18 ga Galvanized structural steel studs on your wall and 6" 18ga structural steel studs laid flat legs down. 1@1/2 elevation. Call the people who make block styrofoam and get them to run you 2@1/2 thick pcs and place them between studs. Cover the walls with frp $32. 4 x 8 at hd Lowe's All these are mold and rot free and not to high in price.

    Has anyone ever shoot gunite on your walls and floor, gunite holds water in pool and will keep water out.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Basement finishing [ 17 Answers ]

I am in the early stages of laying-out my basement plans. There is a rough-in for toilet and shower, but not where I want the bathroom to be. I would like to move the rough-in pipes about 10-12 feet from where they are now for my ideal basement plan. I've done a lot of DIY home pprojects, but...

Finishing Basement with 1/2 bath [ 3 Answers ]

HI MIKE, I APOLOGIZE FOR THE DELAY BUT I NEEDED TIME TO STUDY AND RESEARCH YOUR PREPOSAL. I'M GOING TO USE A LITTLE DIFFERENT FORMAT IN ANSWERING. I'LL EDIT YOUR POST AND ANSWER IN CAPS. I was getting ready to finish my basement and plan to install a 1/2 bath myself (toilet and lavatory). My...

Finishing Basement (Newbie) [ 2 Answers ]

I am currently in the process of finishing my basement. I have done the framing, run the electric and I am in the process of running the plumbing. Next step will be deciding if I can add a couple vents to the area. I admit I do not know much about HVAC. I am in the process of doing my homework...

Finishing basement bathroom [ 17 Answers ]

When we built our house three years ago, we had the basement roughed in for a bathroom. I had talked to the plumber at that time about what would need to be done in the future, but alas have forgotten completely... :) Attached is a picture of the rough in prior to pouring the basement floor. ...

Finishing Bath in Basement [ 4 Answers ]

Hi - My builder roughed in a bath in the basement of our recently constructed home (2 yrs. Old). I've almost finished the basement, and need to complete the bath. I'm no plumber, but I'm pretty handy and have glued my share of PVC in the past. I'm hoping you can help me through the process! ...


View more questions Search