Ask Experts Questions for FREE Help !
Ask
    STONECOTTO's Avatar
    STONECOTTO Posts: 25, Reputation: 1
    New Member
    		  
    #1

    Oct 7, 2007, 09:33 AM
    Kitchen remodel
    Am doing a kichen remodel and I have 100 watts panel with 3 spaces one for the range one for the refrigarator I want to install 12 outlet and 7 reses lighting is this enough circuts or I need to buy a sub panel.
    Fr_Chuck's Avatar
    Fr_Chuck Posts: 81,301, Reputation: 7692
    Expert
    		  
    #2

    Oct 7, 2007, 09:42 AM
    First if this is a remodel, you should already have the space for the stove in your pannel. A stove is normally a 50 amp 220 breaker if it is electric ( not if it is a gas) A 220 stove will take two spaces.
    STONECOTTO's Avatar
    STONECOTTO Posts: 25, Reputation: 1
    New Member
    		  
    #3

    Oct 7, 2007, 10:14 AM
    The previos owner move the kitchen to a smaller space in the house is 19by 8 so iwant to move it to the original place with is 12by12. So will hve to put new lighting and out lets.
    tkrussell's Avatar
    tkrussell Posts: 9,659, Reputation: 725
    Uber Member
    		  
    #4

    Oct 7, 2007, 12:48 PM
    You will need a subpanel, 12- 16 should be fine. Feed with a 60 Amp feeder, and use for all 120 volt loads. Need at least two 20 amp appliance circuits for the counter, all kitchen outlets are GFI, except reefer. Best the reefer be a separate circuits, and any microwaves, and dishwasher.

    You should be able to use a 40 amp range circuit, most besides the larger ones fit fine.
    STONECOTTO's Avatar
    STONECOTTO Posts: 25, Reputation: 1
    New Member
    		  
    #5

    Oct 7, 2007, 02:26 PM
    Sorry but what does 12-16 means thank you
    tkrussell's Avatar
    tkrussell Posts: 9,659, Reputation: 725
    Uber Member
    		  
    #6

    Oct 7, 2007, 03:37 PM
    Oh sorry, 12 to 16 circuit panel board.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Kitchen remodel [ 5 Answers ]

We need to install our sink and the dishwasher, the existing drain pipe for this is currently blocking the dishwasher in the back. I need to know if I can change the drain from the current pipe into a 2 inch vent pipe. Tough question to ask and hard to describe. Any help would be wonderful.

Fireplace Remodel [ 1 Answers ]

:confused: My husband and I are in the beginning stages of a living room 'make-over'. Our fireplace is now painted white with blue grout (yuck). Do I need to remove the old paint before we repaint it? Do we need a specific type of paint, or a primer? thanks

Kitchen Remodel - Venting and Draining Questions [ 2 Answers ]

Two Questions, Same Project: 1) I have remodelled our kitchen, moving the kitchen sink to the other side of the room, so the existing vent is not accessible at the normal location in the kitchen cabinet just after, but above the P trap. Fortunately, I have a full basement below, and can easily...

Bathroom remodel [ 6 Answers ]

I'm working on a remodel of my older home. Cast iron piping was used for the drains and galvanized for venting. The garage was converted in to a bedroom and they built a 1-1/2 bathroom. Now for the fun part, since it was a garage it has cement slab they laid the original 4" cast iron drain...

Remodeling a remodel [ 3 Answers ]

A ceiling light was removed during a previous remodel and power was directed to supply a ceiling fan with a light kit installed. The ceiling fan was subsequently replaced with another unit (also with a light kit installed.) At the old box there is currently no light fixture. Just a bundle of...

View more questions Search