Ask Experts Questions for FREE Help !
Ask
    Active3's Avatar
    Active3 Posts: 2, Reputation: 1
    New Member
     
    #1

    Jun 30, 2007, 09:47 AM
    Cast Iron Vent Stack
    I have just purchased a 1950's rental property with a cast iron vent stack. The insurance co. wants me to replace it as they are prone to leaking in older homes. The job seems fairly straight forward, but do you have to replace the elbow/cleanout at the bottom that is cemented into the basement floor or can you just replave from that fitting up?
    I have also been reading that a 4" cast pipe can be replaced by a 3"pvc. It is a small home do I need to replace with 4"pvc or is 3" OK?

    Thanks

    Tom
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
     
    #2

    Jun 30, 2007, 11:11 AM
    You will have to check local codes to find out if you can reduce from 4 to 3" on your stack. In my area we are allowed to use 3" for the main stack in our new home construction. I shouldn't think that you will be forced to bust up cement and replace the bend at the base of the stack. On a side note, my house is 53 7years old with cast iron drainage but have had no leaks. As a vent stack carries no discharge or water was it "suggested" or "ordered" that you replace the cast iron with PVC? In my book you shouldn't have to unless there's a problem with the present stack.
    Good luck, Tom
    Active3's Avatar
    Active3 Posts: 2, Reputation: 1
    New Member
     
    #3

    Jul 1, 2007, 09:37 AM
    You will have to check local codes to find out if you can reduce from 4 to 3" on your stack. In my area we are allowed to use 3" for the main stack in our new home construction.

    Thanks, I did check & you are right 3" is adequate

    I shouldn't think that you will be forced to bust up cement and replace the bend at the base of the stack.

    I will leave that part as is

    On a side note, my house is 53 7years old with cast iron drainage but have had no leaks. As a vent stack carries no discharge or water was it "suggested" or "ordered" that you replace the cast iron with PVC? In my book you shouldn't have to unless there's a problem with the present stack.

    That would seem reasonable, it was my insurance company who said that they want this done in order to keep my rates lower. As you noted, it does not carry water, so what the big deal is, I am not certain.
    Good luck, Tom[/QUOTE]

    Thanks

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Can I replace part of my cast iron sewer stack. [ 3 Answers ]

I have a hopefully not too stupid question about replacing part of my cast iron sewer stack. I have a 50+ year old house with roots in my sewer pipe causing some backup thought the basement drain. I used root killer in the drain and several weeks later had a mat of small roots flush back up...

Crack in Cast Iron Main soil stack [ 3 Answers ]

:confused: I just moved into a Bi-level house approx. 40-50 years old. It has a Cast Iron Main soil stack (main vertical sewer line). On the lower level I noticed that it has a crack that is approx 5"-6" long about 1/4" thick. Now I bought a new pluming book because of some other repairs I had...

Cast iron soil stack to pvc [ 15 Answers ]

the plumbing in our house is from 1936. We noticed a large stain in the ceiling, tore it out to reveal the cast iron soil stack (runs from the upstairs bathroom turns a corner then runs straight to the basement) and found the leak was around (very bad leak) the lead joint. My husband finally got...

Cast Iron Main Vent [ 5 Answers ]

Just looked at a property I want to buy and flip. During inspection, two red flags for me. About a 40' run of cast iron drain pipe is rusted and leaking. All radiators need to be moved to maximize space. Q1: My question is: Is the job of replacing the cast iron to tough for a DIY'er like me?...

Cast iron vent stack [ 7 Answers ]

I'm installiing a new basement bathroom and when running a vent stack I would like to tap into the existing cast iron with PVC using a saddle on the cast. My question is what method is used to cut a hole in the cast iron, where I wish to place the saddle and connect the PVC.


View more questions Search