Ask Experts Questions for FREE Help !
Ask
    redant360's Avatar
    redant360 Posts: 8, Reputation: 2
    New Member
    		  
    #1

    Jun 27, 2007, 09:20 PM
    Locating a Die-cast metal 1980's generation "Side Swipe" Transformer
    Does anyone know if the Transformer "Side swipe" was ever produced in Die cast
    Metal around 1 to 24 scale size? And if so, where to obtain one from?

    It can be a re-issue of the 1980's transformer but must have the following features:
    - Die-cast metal exterior panels
    - A red Lamborghini
    - Around 1 to 24 scale in size (roughly 200mm long by 90mm wide I think)

    Any info would be greatly appreciated as I had mine stolen when I was a kid:(
    JSCHOR1234's Avatar
    JSCHOR1234 Posts: 2, Reputation: 2
    New Member
    		  
    #2

    Jun 18, 2009, 06:13 PM
    Did you try "EBAY"? I know they have a lot of transformers for sale
    redant360's Avatar
    redant360 Posts: 8, Reputation: 2
    New Member
    		  
    #3

    Jun 18, 2009, 06:23 PM
    I have since discovered that it was in fact my sense of scale
    As a very little kid that had misguided my perception of the
    Size of this toy. The Side Swipe Transformer of the 1980's
    Was only ever produced in one size.
    MoreThenMeets's Avatar
    MoreThenMeets Posts: 2, Reputation: 1
    New Member
    		  
    #4

    Jun 29, 2010, 03:58 PM
    Hi.. I am looking for a die-cast Optimus Prime in the 1980's. I used to own one but lost it while moving. Shame on me. Checked on eBay as well as many other websites but can not find anything. Any suggestions appreciate.
    MoreThenMeets's Avatar
    MoreThenMeets Posts: 2, Reputation: 1
    New Member
    		  
    #5

    Jun 29, 2010, 03:58 PM
    Hi.. I am looking for a die-cast Optimus Prime in the 1980's. I used to own one but lost it while moving. Shame on me. Checked on eBay as well as many other websites but can not find anything. Any suggestions appreciate.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Cast Iron: plug stuck in 3" x 1.5" Tee [ 5 Answers ]

Hey there! I've got a 3" cast iron soil stack, with a 1 1/2" Tee fitting which has a plug in it. There's some goop at the joint, it's pretty hard. Not quite JB-weld hard, but hard. It's beige colored. There's not a lot of room in the space, but I've gotten an 18" pipe wrench on it and i...

PVC to Cast iron "Speed bump" [ 1 Answers ]

Hello all, I call this thread the speed bump because when I dug out my basement floor to replace an upstream section of cast iron pipe with new pvc pipe for a bathroom and to move my stack, the downstream attachemtn to the cast iron pipe is now giving me some mild trouble. The cross section of...

Toilet , 4" pvc to 3" cast [ 4 Answers ]

I have a home with a basement and problems with a toilet on the first floor. I had to repair the floor because the old cast flange was leaking. I cut out The flange and around 4 foot of old cast 3" pipe. I repaired the floor and used a 4" pvc flange and 4" pvc pipe with a 4"to3" rubber boot to...

Tstat wiring - dual transformer, 1 "R" connection [ 1 Answers ]

I have a dual transformer system - one for heat, one for cool. The Thermostat I'm replacing has an Rc and an Rh connection. The new Thermostat has a single R connection. The transformers are in phase With each other, however, the heat one puts out 24vac, while the Cooling one is at 26.7vac. Can...

Shower flange"cast iron" [ 3 Answers ]

I have a stand alone shower on a slab foundation that leaked I pulled the floor out and the cast iron flange for the liner is in bad shape and needs to be replaced. How do I go about this and where do I get the parts.

View more questions Search