Ask Experts Questions for FREE Help !
Ask
    Bigadd's Avatar
    Bigadd Posts: 1, Reputation: 1
    New Member
    		  
    #1

    Sep 6, 2006, 10:01 AM
    Installing a photo cell into an existing circuit
    I want to install a photo cell on an electrical circuit that runs to an outside light fixture. There is a black and white wire (and ground) from the house, a black and white wire in the fixture, and the photo cell has a black, white, and red wire.
    What is the correct wiring schematic that will allow the photo cell to turn my light off and on?
    Thanks.
    Bigadd
    tkrussell's Avatar
    tkrussell Posts: 9,659, Reputation: 725
    Uber Member
    		  
    #2

    Sep 6, 2006, 10:45 AM
    At the junction where the photocell will be connected, splice all the whites together. The feed black connects to the black on the photocell, the red from the PC connects to the fixture.
    detsgtrico's Avatar
    detsgtrico Posts: 1, Reputation: 1
    New Member
    		  
    #3

    Mar 27, 2008, 04:32 PM
    How to install a photocell to a new luminary wall mounted light fixture.
    ceilingfanrepair's Avatar
    ceilingfanrepair Posts: 5,733, Reputation: 109
    Uber Member
    		  
    #4

    Mar 27, 2008, 05:06 PM
    Wow, your terminology sounds rather technical.
    kaitlyn30's Avatar
    kaitlyn30 Posts: 1, Reputation: 1
    New Member
    		  
    #5

    Nov 30, 2010, 07:41 PM
    I installed a photo control light outside the connection from the breaker to the light had no ground wire so I connected the ground from the light directly to the j-box. I turned on the breaker and the light started to turn on then after a few second it turned off so I tested the hot and neutral and both were fine so my question is will the light turn on at dusk is that why it is called photo control
    donf's Avatar
    donf Posts: 5,679, Reputation: 582
    Printers & Electronics Expert
    		  
    #6

    Dec 1, 2010, 08:17 AM

    Kaitlyn,

    Welcome to our forum. By now you should have the answer to your question.

    A photocell turns on at dusk and off at daylight.

    In the future, please check the date of the item you are appending to. This original post is over two years old.

    You would get a faster response by opening a new thread.

    Once again, welcome.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Adding a heater to an existing circuit. [ 3 Answers ]

I want to place a 240V electric base board heater in a room. In the adjacent room I have a conveniently placed electric wall oven by itself on a 50 Amp circuit with 8 gauge wire. The oven is only rated at 30 Amps and the heater at 4.5 amps. So, I want to run wire from the oven to where the...

3d photo [ 1 Answers ]

I have a pictue in 3d of an eagle landing on a branch ==how are these made

Photo cell [ 1 Answers ]

How can I build a simpel photocell circuit

Outside GFI circuit - 15amp outlet on 20amp circuit [ 1 Answers ]

I need a better understanding of what I should do when setting up my new outdoor circuit. I've got a circuit that runs about 150 feet, so I'm installing 10g wire to allow for the voltage drop. I read in the Home Depot Electrical 123 book that I can have at most a 15amp circuit with 10g wire on...

View more questions Search