 |
|
|
 |
New Member
|
|
Jan 17, 2008, 07:15 PM
|
|
|
How do I check to see if it is out of time? Sheared pin or?
Briggs and Stratton 18.5 HP OHV
How do I check to see if it is out of time? Sheared pin or?
|
|
|
|
Ultra Member
|
|
Jan 19, 2008, 06:39 AM
|
|
|
You remove the blower housing from the top of the engine and remove the nut from the top of the flywheel. Then you will be able to see if the groove in the crankshaft and the groove in the flywheel are aligned. If not, the flywheel key is sheared and you will have to remove the flywheel from the crankshaft. USE A FLYWHEEL PULLER to perform this feat. Don't make the common mistake of prying with screwdrivers, or prybars as you can damage the magnets of the flywheel or worst yet, crack or bust the engine housing. Use extreme caution and care. Be sure to torque all items back to specs when re assembling.
|
|
|
 |
Home Repair & Remodeling Expert
|
|
Jan 20, 2008, 05:53 PM
|
|
|
Sorry Mower but I got to spread some around before I can give you another accurate rating but this is certainlly accurate advice. Right on down to how not break a flywheel. Oh well, less work for us again, sigh.
|
|
|
 |
Ultra Member
|
|
Jan 20, 2008, 06:49 PM
|
|
|
I can help out here, ball. Mowerman always gives good, detailed advise
|
|
|
|
Ultra Member
|
|
Jan 21, 2008, 06:24 AM
|
|
|
Thanks you!
Freebird, have you found your problem?
|
|
|
|
New Member
|
|
Mar 5, 2008, 09:39 AM
|
|
|
 Originally Posted by MOWERMAN2468
thanks ya'll!
freebird, have you found your problem?
Well I put a new key in. and found a stuck valve which I beleave is the culpret for bending the aluminum push rod. I disasembeld the head and cleaned valves and ground them and seated them. Now it runs but not much power and the muffler gets red hot. So I'm thinking maybe I should have replaced w/new valves. I set exhaust (bigger valve on bottom at .009 and the intake. (smaller valve on top at .005 I turned motor over till piston came all the way up so that both exhaust and intake were no pressure on valve springs. I just don.t know what else to do. Could the cam have jumped time? :confused: :confused:
|
|
|
|
Ultra Member
|
|
Mar 5, 2008, 05:52 PM
|
|
|
Okay, rotate the engine to TDC and go 1/4" (one quarter of an inch), past TDC. Then set the valves at .004" intake, and .005" exhaust.
|
|
|
| Question Tools |
Search this Question |
|
|
|
Add your answer here.
Check out some similar questions!
Theft under $5000. 2nd time. But 1st time since 18th
[ 4 Answers ]
Hey all,
So basically the story goes like this:
In April of 2006, I was arrested for theft under $5000 for car prowling in a neighborhood and some alleyways. I was 17 at the time. We got caught with $1500 worth of golf clubs in the back of my dads car. Needless to say, my dad was pissed....
Where do you find the plug in to check the check engine light
[ 16 Answers ]
I am trying to find the plug in where you plug in the computer to check the check engine light it a 1992 civic can anyone tell me where it located at and if you have picture that would be great thanks if you could tell me the color of the plug in and how many pin in it that would help me in finding...
Disability check VS. Child support check
[ 2 Answers ]
My sister lives w/ my step father. My mom HAD to leave the home. My sister is 13 and decided to stay w/ father. I don't think he can take care of my sister.. he can't hardly take care of his self. He receives a disability check for his self and my sister gets one also until she is 18. He BLOWS...
Me and my son ssi check at tax time
[ 2 Answers ]
I have a son that get ssi,
He just turn 18 this past sept 16, 2007
He lived with me till he turn 18,
I haven't reported this to ssi , cause we were waiting to see if this was going to last with him out on his own, he has moved in with his cousin. And has been there for 2 months now.
But...
View more questions
Search
|
