Ask Experts Questions for FREE Help !
Ask
    cdparson's Avatar
    cdparson Posts: 2, Reputation: 1
    New Member
    		  
    #1

    Mar 1, 2008, 09:13 PM
    Shower stall repair
    The former owner installed or had installed a shower incorrectly. The biggest problem is that the valve was not secured to the studs. It is floating around in the wall. Trying to repair a drip I took the cover off and cannot get it back on. The screws will not secure to anything. I guess I am reduced to cutting open the unit and making the necessary repairs. Is there any decent way to do this and patch it so that it will look acceptable in the future? If so, how?
    hkstroud's Avatar
    hkstroud Posts: 11,929, Reputation: 899
    Home Improvement & Construction Expert
    		  
    #2

    Mar 1, 2008, 10:35 PM
    What kind of walls does your shower have, tile, fiber glass or shower surround? What kind of valve is it?
    Could you access the valve by going in thur the other side of the wall?
    Can you show us a picture?
    cdparson's Avatar
    cdparson Posts: 2, Reputation: 1
    New Member
    		  
    #3

    Mar 2, 2008, 07:33 AM
    The shower is a fiberglass surround unit with no seams. The valve is a central unit in the center of the back wall.
    The idea to come in from the back is a possibility. Any problems to try to miss on such a procedure. I do not believe there are any wires in this section but would be careful.
    massplumber2008's Avatar
    massplumber2008 Posts: 12,832, Reputation: 1212
    Senior Plumbing Expert
    		  
    #4

    Mar 2, 2008, 07:47 AM
    Hey CD... go out to the home supply store and purchase a screw that is like 2 inches longer than the screw you pulled out of valve. Most valves need two screws to screw in cover plate... so you can use the longer screw to catch the thread and begin pulling in until the other normal screw can get caught.. screw that in a few threads, then release the really long screw and then install the other normal screw. Tighten these and you should be back to where you were before starting.

    If did not like how it was before then stick with Harold.. he will guide you through the process nicely! Hi Harold! *waving*...

    Could also install a symmons remodeler plate (or similar) from the front and secure the valve if you really wanted too secure it correctly (see pic.)... just another thought. Take care.
    Attached Images
     
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
    		  
    #5

    Mar 2, 2008, 07:57 AM
    . Don't cut any holes in the wall yet until you try this.Work a piece of fur strip or a small piece of wood on top of the valve body and the vertical shower raiser. This will serve as backing. Now tie a string on the valve body so it can be pulled close to the enclosure. Pull the valve body close and place the chrome cover plate and screws in position to start the screws. Snug up the screws until they are tight. Your valve should now be secured. Simply pull on the string until it breaks and you're done. Good luck, Tom
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Repair or Replace Basement Shower Stall [ 1 Answers ]

Hi, I'm wanting to repair/replace the shower stall in the basement because at the bottom it's pretty rusted. I think it's called a freestanding stall. I wanted to avoid replacing the stall, because the base--which really doesn't need to be replaced--measures 31 1/2". The bases that come with...

Shower stall repair [ 2 Answers ]

Hi, About a week ago, the paint on the base of our shower stall in the master bathroom started "bubbling" and we were able to start to peel it off. We were told that the previous owners probably painted it just before they put the house on the market to sell. That was 3years ago. My...

Shower stall need height of controls and shower head [ 1 Answers ]

Hi Am building a shower and require the height of the taps and the shower head

Turning walking shower stall into bathtub/shower combo. [ 4 Answers ]

Question: Current shower drain (2" pipe) runs 5 feet, under slab, to vent stack (5" cast iron vent pipe) of toilet. Will need to move the drain 3ft to wall for new tub. After moving the drain, the complete length of the pipe will still be around 5 feet. We will have to reduce the drain line...

View more questions Search