Ask Experts Questions for FREE Help !
Ask
    kbcb1080's Avatar
    kbcb1080 Posts: 1, Reputation: 1
    New Member
     
    #1

    Jan 21, 2008, 05:18 PM
    Troubleshooting with replacing a bathroom sink.
    Hi-

    My husband and I are first time homeowners and we are trying to replace the sink that is about 30 years old in our powder room. The snag that we have run into is that, the washers on water lines are not able to be loosened with using a wrench. In fact with increased pressure the pipe that leads to the water line starts to bend. I was wondering if someone could help me with suggestions for a different tool to use, or possible solutions that could make the washer loosen without stripping the washers completely or bending the pipe that leads to the water line.
    KISS's Avatar
    KISS Posts: 12,510, Reputation: 839
    Uber Member
     
    #2

    Jan 21, 2008, 05:46 PM
    I think you mean nuts - things that usually have 6 flats.
    Washers are circular with a hole in the center.

    Snap a picture. Post it using "Go advanced."

    All fittings should be loosened and tightened with two wrenches.

    You MAY have to replace the "angle stop". That's the valve with a outgoing pipe at 90 deg. From the incoming one angle if it's that old.
    ballengerb1's Avatar
    ballengerb1 Posts: 27,378, Reputation: 2280
    Home Repair & Remodeling Expert
     
    #3

    Jan 21, 2008, 07:22 PM
    Sorry but I did have to chuckle, those nuts may even be on a flexible supply line if they run up from the stop to the sink. In any case you need two wrenches like KISS says. One hold the item to be unscrewed and the other holds what it is screwed into.
    cgregory67's Avatar
    cgregory67 Posts: 92, Reputation: 7
    Junior Member
     
    #4

    Jan 21, 2008, 10:02 PM
    Make sure your water is off, and cut the lines above the shut-off valves. They are probably plastic or rubber hose. Some may be copper but you will replace these no matter what type for only a few dollars.

    After you cut them disconnect drain pipes and rip the sink top off by hammering on edge upward, this is only glued on. Now you can see inside the cabinet, there might be screws or nails securing it to the walls. Remove entire cabinet now and then wrestle with the line nuts while everything open and out of the way. Use two wrenches; one to loosen, and one to hold pipe still as suggested above.

    Good luck and bravo for doing it yourselves!
    glavine's Avatar
    glavine Posts: 895, Reputation: 87
    Senior Member
     
    #5

    Jan 22, 2008, 08:30 PM
    Id try some wd40 and see if that will loosen them up. With 30yrs it may be rusted a little inside there. You do need to be careful about twisting a lot , it could crack the pipe. If that doesn't work id cut the water off from the house not just the sink, but the whole house, then take a pipe cutter and cut the supply lines off if there is room to do so. Then buy some new pressure fitting (on/off valves) attach those and buy some new supply line for a couple bucks

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Replacing bathroom sink shut off valve [ 3 Answers ]

The shut off valve for the bathroom sink is really old and can not be turned off. The bathroom remodel will take awhile so I can't go that long without water in the whole house. What is needed to replace the existing shut off valve so that we can remove the old sink and continue work on the...

Replacing bathroom single sink with double [ 2 Answers ]

I am replacing the bathroom vanity from a single sink to a double sink. Problem is that the current drain is in the middle of the vanity and I would like to maximize drawer space here. Can I move the existing trap parallel, against the wall and put a tee connection over this for the double sinks?...

Replacing J pipe under bathroom sink [ 1 Answers ]

Can I get some instructions on how to do this properly? It had started to leak at the connection under the sink, and when I went to inspect it it just came apart! I have the parts to replace it. I don't want to call a plumber just for this. It seems like it should be simple but of course is not...

Pipe snapped replacing bathroom sink [ 3 Answers ]

My cold water pipe snapped behind the shut off valve on the threads inside the wall. I do not know how to weld properly and the main water supply for the whole house is shut off. What do I do? Is it possible to bypass just one bathroom sink and allow water through out the rest of the house?

Replacing Sink Base, need a double sink? [ 1 Answers ]

Hello. I just bought my first condo, and immediately changed the appliances (my fridge is now larger than the previous one at 30 inches wide (normal I know). I am not replacing the cabinets. I have limited space on one wall, so I need to DOWNGRADE from a 36 inch SINK BASE to a 33 inch SINK BASE....


View more questions Search