Ask Experts Questions for FREE Help !
Ask
    leez1234's Avatar
    leez1234 Posts: 1, Reputation: 1
    New Member
     
    #1

    Jan 5, 2008, 03:47 PM
    Removing shut off valves under bathroom sink.
    I had a problem after I insstalled a new sink faucet. I had a small drip coming from the cold water shut off valve below the sink. No matter how I tightened or loosened it, the screw in front and the knob itself, it would still drip slowly. So I figuered I would just replace the valve. I bought a new valve and tried to unscrew the large nut against the wall to replace the valve. Ok there doesn't seem to be threads, and it won't come off. I believe there is copper attached to it. My house is 27 years old. So now what, how do I remove the valve, to replace it with a new one. Did I damage anything turning the large nut/
    ballengerb1's Avatar
    ballengerb1 Posts: 27,378, Reputation: 2280
    Home Repair & Remodeling Expert
     
    #2

    Jan 5, 2008, 04:16 PM
    Your old valve apparently is a sweat fitting that is soldered to a copper pipe. Do not worry about that nut, you are closed to throwing it out. Shut off your main and open a faucet to blow off pressure. Disconnect the suplly line going up to the sink faucet and open the old shut off valve, stop cock. Heat the valve to melt the old solder and pull out while still hot. Wipe the molten solder off the pipe with an old rag. Take the old stop to the hardware store to get a perfect match, thgen sweat the new fitting onto the old pipe.
    labman's Avatar
    labman Posts: 10,580, Reputation: 551
    Uber Member
     
    #3

    Jan 5, 2008, 07:36 PM
    If the end is a hex, likely it is pipe thread or compression fitting. One will turn one way, and the other, the other way. If you can't see any thread between the valve and wall, likely it is a compression fitting and you turn the top of it to the right to loosen.

    By the way, where is it leaking? Maybe you can fix it.
    KISS's Avatar
    KISS Posts: 12,510, Reputation: 839
    Uber Member
     
    #4

    Jan 5, 2008, 09:42 PM
    Picture? Use "Go advanced" to post one.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Replacing bathroom sink shut off valve [ 3 Answers ]

The shut off valve for the bathroom sink is really old and can not be turned off. The bathroom remodel will take awhile so I can't go that long without water in the whole house. What is needed to replace the existing shut off valve so that we can remove the old sink and continue work on the...

Removing old Bathroom Sink Fixture [ 1 Answers ]

I am trying to remove an old bathroom sink fixture, including the stopper and have run into a problem. I have removed everything except the 5 inch piping used for the drain that connects directly to the u-shaped pipe carrying the water out. I can't remove the washer at the top of this pipe,...

Shut off valves [ 8 Answers ]

This is my problem. I have moved into an older home and I am doing some remodeling and when I went to remove the countertop and sink in the bathroom, I found that plastic piping came through the floor and directly to the faucets. I wish to put a shut off valve on the plastic pipe after shutting...

Bathroom sink hot water shut-off valve [ 6 Answers ]

I live in a house on columns. In following the instructions for removing a bathroom sink faucet I turned the shut-off valves off. The cold side did not run, but I am getting a drip from the hot side... a drop every second or two. I tried shutting off the supply downstairs. But the drip persists....

Access to shut off valves [ 1 Answers ]

Does anyone know if there is a code in sarasota fl that says you must have access to shut off valves in your tubs and if so what is that code and where can I get a copy. Thank you[ Manny


View more questions Search