Ask Experts Questions for FREE Help !
Ask
    Brucem55's Avatar
    Brucem55 Posts: 4, Reputation: 1
    New Member
     
    #1

    Nov 12, 2007, 05:09 AM
    Low water pressure when 2 or more faucets are on
    Why does the water pressure in my house drop to almost nothing when 2 or more faucets are turned on?:confused:
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
     
    #2

    Nov 12, 2007, 06:18 AM
    Quote Originally Posted by Brucem55
    why does the water pressure in my house drop to almost nothing when 2 or more faucets are turned on?:confused:
    How old is your house? What material are your pipes made of. Copper, plastic or galvanized? Did this happen all of a sudden or come on slowly?
    Brucem55's Avatar
    Brucem55 Posts: 4, Reputation: 1
    New Member
     
    #3

    Nov 12, 2007, 08:35 AM
    House was built in 1974
    Copper Pipes
    After third bathroom was added problem started.
    ballengerb1's Avatar
    ballengerb1 Posts: 27,378, Reputation: 2280
    Home Repair & Remodeling Expert
     
    #4

    Nov 12, 2007, 09:01 AM
    I'll bet the third bath was just tapped onto the original piping which was not sized for this many fixtures. Check to see the size of the pipe they tapped into, could be a small line about 3/8" and that is way too small to have two or more rooms on it. Once you track this down Tom can talk you through ways to repipe the third room, if the pipes are exposed in the basement or crawl it won't be too bad.
    Brucem55's Avatar
    Brucem55 Posts: 4, Reputation: 1
    New Member
     
    #5

    Nov 12, 2007, 09:24 AM
    They tapped into the opriginal piping, but used 1/2 just like the original sizing. This was all inspected by a city engineer and should not be outside those parameters, but I will check with them as well.
    The plumbing they tapped into is in the wall on the second floor and I ican get to it, I ijust have to create a door for it for future repairs.
    I will double check the plumbing.
    Thanks
    ballengerb1's Avatar
    ballengerb1 Posts: 27,378, Reputation: 2280
    Home Repair & Remodeling Expert
     
    #6

    Nov 12, 2007, 09:29 AM
    If they tapped into a 1/2 " line with another 1/2 " line the flow will be greatly impaired if a faucet or fixture is used in two locations at the same time. Piping is a bit like air ducts that start large and get progressively smaller as they go downstream. Anytime you tap into the end of the run there will be pressure issues. Let us now what you find once you cut your opening. Doubt that a city engineer actaully inspected your job, lucky to get a building inspector.
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
     
    #7

    Nov 12, 2007, 10:16 AM
    After third bathroom was added problem started.
    It's not the new size of the 1/2" branches that concern me but the pipes they connected the 1/2" pipes to. If they came off another 1/2" pipe you have located the problem . There should be no more then three fixtures being supplied by a 1/2" branch. Any more fixtures on a 1/2" branch and you began to run into volume and pressure problems if too many are in use at the same time. Both hot and cold branches to the new bathroom group should have been taken off a 3/4" main. Regards, tom
    Brucem55's Avatar
    Brucem55 Posts: 4, Reputation: 1
    New Member
     
    #8

    Nov 12, 2007, 01:19 PM
    It was a building inspector, my bad.
    Speedball1,
    I have to go with what your saying, my father was a plumber for 30 years before he died in 1983 and I now remember him saying all bathrooms should have their own line coming of the main coming into the house.
    I can tap in the cold and hot water in the water closet can't I ?

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Low hot water pressure through the whole house even ater replacing water heater [ 2 Answers ]

I'm still experiencing low hot water pressure even after replacing the water heater. When you first turn on the faucets the pressure will be fine but within a few seconds it drops again.

Temporary loss of hot water pressure in all faucets [ 1 Answers ]

I actually have two plumbing problems. We moved into a 9 year old home about 1 year ago. In March, we had a water softener installed. The previous owners never installed a softener. I'm not sure if the softener installation has anthing to do with this, but we've been experiencing temporary loss...

Low Pressure and Low Flow Water Supply [ 4 Answers ]

I recently moved into a house that is about 6 years old. The house sits upon a small hill. The water pressure is 40 psi at the street and the flow rate is 13 gpm. At the house, the pressure is about 30 psi and the flow rate is 3.5 gpm. The house is higher than the street level, but the...

Low water pressure in an area known for high pressure [ 3 Answers ]

Greetings, My wife and I are in the process of updating 1957 side by side split level. The previous owner (OK, my Mom as I bought the house I grew up in from her) said that when they moved in they had to install a pressure reducer into the line. I have searched high and low but, I can't see...

Low hot water pressure in a couple faucets [ 3 Answers ]

Within the last 48 hours, two faucets suddenly have really poor hot water pressure. The kitchen faucet has low pressure on hot; on cold it is fine. Right around the corner in the half bath, the hot water pressure is great. Upstairs in the bathroom we have a double sink; one of the hot waters...


View more questions Search