Ask Experts Questions for FREE Help !
Ask
    ksbear's Avatar
    ksbear Posts: 3, Reputation: 1
    New Member
     
    #1

    Jul 22, 2007, 09:25 AM
    Shower drainage slow
    We removed our old tub/shower and put in a new shower stall only. We moved the shower to the opposite wall and had to move some plumbing and the sewer hook up. The couple times we used it it worked fine. Now it drains very very slowly. This is what we did. We moved the shower drain approximately 3 feet, installed 2 in. ABS drain and p-trap with a 1/4 -3/8 in. drop per foot into the existing plumbing. We tied into the existing vent which was there for the tub. Do I need a vent closer to the shower or before the shower?
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
     
    #2

    Jul 22, 2007, 10:55 AM
    At three feet your vent falls within code. Are there any 90's in the drain line? Is it possible that mortar or some trash fell down the drain during installation? Regards, Tom
    cavitywall's Avatar
    cavitywall Posts: 6, Reputation: 1
    New Member
     
    #3

    Jul 22, 2007, 11:03 AM
    Quote Originally Posted by ksbear
    We removed our old tub/shower and put in a new shower stall only. We moved the shower to the opposite wall and had to move some plumbing and the sewer hook up. The couple times we used it it worked fine. Now it drains very very slowly. This is what we did. We moved the shower drain approximately 3 feet, installed 2 in. ABS drain and p-trap with a 1/4 -3/8 in. drop per foot into the existing plumbing. We tied into the existing vent which was there for the tub. Do I need a vent closer to the shower or before the shower?
    With water in shower, use a plunger, fast and slow to see if you can tell anything. Any open ends you can plug in sequence may help give a clue. Check behavior of adjacent drains while you're plunging. Something's got to give.
    ksbear's Avatar
    ksbear Posts: 3, Reputation: 1
    New Member
     
    #4

    Jul 22, 2007, 10:14 PM
    Quote Originally Posted by speedball1
    At three feet your vent falls within code. Are there any 90's in the drain line? Is it possible that mortar or some trash fell down the drain during installation? Regards, Tom
    Thanks for your help. It turned out that that is just what happened. We ran a snake and pulled out some insulation. We are free flowing now!!
    ksbear's Avatar
    ksbear Posts: 3, Reputation: 1
    New Member
     
    #5

    Jul 22, 2007, 10:18 PM
    Quote Originally Posted by cavitywall
    With water in shower, use a plunger, fast and slow to see if you can tell anything. Any open ends you can plug in sequence may help give a clue. Check behavior of adjacent drains while you're plunging. Something's gotta give.
    We tried the plunger option and it didn't seem to change anything. We ran a snake and pulled out some insulation. Works great know. Thanks!!

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Alternating slow/fast drainage [ 4 Answers ]

Dear Community, I have a sink in my bathroom which can't decide whether it wants to be clogged or not. After running the water continuously for about a minute with the drain open, water starts to accumulate in the sink. When the depth of water is about two inches (still running the water at...

Venting/Drainage a new Bathtub into an existing sunk in shower [ 2 Answers ]

Okay, Basically. The sunk-in shower is obviously lower than the bath tub. And I wish to connect the new drain from the tub to the existing 2" drain from the shower. My question is: How would I go about venting (if needed) and connecting the new tub that is 4' away from the existing drain, Without,...

Slow tub drainage [ 16 Answers ]

We recently remodeled bathroom. Replaced sewer line for tub/shower. Put in new drain/tub/shower etc. I expected the tub to drain with voracity. But it does not. When the washer drains into the washtub in utility room, the water still backs up into the tub. Very disappointed. What causes...

Standing bath shower is filled with drainage stuff-Please help [ 3 Answers ]

Hi, I've got quite a situation going here. I own single family house (Rambler Type), and have a main level and a Basement. The Main level has two full bath rooms and the Basement has one full bathroom (standing bath and a toilet sink). We rarely use the Bath room in the Basement. It is only used by...

Slow shower [ 4 Answers ]

Hello experts, We are having a problem with low shower and tub water flows in both of our bathrooms where we moved in a while ago. The bathroom sink faucets used to flow low, and I was able to get rid of diposits and now they are better. However, I am not sure what to do with showers after...


View more questions Search