Ask Experts Questions for FREE Help !
Ask
    Hilberjj's Avatar
    Hilberjj Posts: 1, Reputation: 1
    New Member
     
    #1

    Aug 31, 2015, 06:35 PM
    Light comes on then goes off.
    After installation all worked well for a couple days. Then light stopped working. Initially the lights would blink then go off. Now they don't come on at all. Power to the fan is good and I think there is a control element that has failed. What are the replacement choices. Read about someone just wiring around the control but I'm sure there was a need for it or the engineers would have deleted the control in the first place. Help.
    Thank you.
    smoothy's Avatar
    smoothy Posts: 25,490, Reputation: 2853
    Uber Member
     
    #2

    Aug 31, 2015, 07:45 PM
    Quote Originally Posted by Hilberjj View Post
    After installation all worked well for a couple days. Then light stopped working. Initially the lights would blink then go off. Now they don't come on at all. Power to the fan is good and I think there is a control element that has failed. What are the replacement choices. Read about someone just wiring around the control but I'm sure there was a need for it or the engineers would have deleted the control in the first place. Help.
    Thank you.
    Is this the light on your Submarine.. your walk in Refrigerator.. or your Bulldozer. You need to tell us what this is on exactly.
    donf's Avatar
    donf Posts: 5,679, Reputation: 582
    Printers & Electronics Expert
     
    #3

    Sep 1, 2015, 03:51 AM
    If the light/fan unit is a new install, take the defective unit back to the store.

    Short of that, help us a little bit more. How is the device connected up?
    hkstroud's Avatar
    hkstroud Posts: 11,929, Reputation: 899
    Home Improvement & Construction Expert
     
    #4

    Sep 1, 2015, 04:06 AM
    Is this the light you refer to?
    Attached Images
     
    ballengerb1's Avatar
    ballengerb1 Posts: 27,378, Reputation: 2280
    Home Repair & Remodeling Expert
     
    #5

    Sep 1, 2015, 09:32 AM
    Who did the install?

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Johnson Air Ease Furnace pilot light won't re-light. Fire there but no pilot light [ 0 Answers ]

Air Ease (Johnson) furnace pilot light will not re-light. Flame sensor replaced three years ago. Flame left on for a couple minutes but sensor will not allow pilot light to stay on. Going out now to try new pilot light flame sensor. NEED HEAT!

Put a bulb converter on light bulb for fan light and now the light doesn't work [ 1 Answers ]

I put a light bulb converter on a ceiling fan light to get more light and now it doesn't work. Fan works fine

Light switch will turn off under cabinet light, but won't turn light back on [ 1 Answers ]

Hi all: I recently installed under cabinet lighting in my kitchen. I added a single pole switch to an existing GFCI outlet, and then wired said switch to a surface mounted receptacle on top of my cabinets. I wired everything up, and the lights work great. The problem: When I turn...

Braking light, TCS light on, ABS light on for 2003 Hyundai sonata V6 [ 1 Answers ]

The braking light, TCS light on, ABS light are always on. I got it checked in car garage and they told me it is the ABS module problem and need about 400 for a used one The code is SCAN ABS, TCS MODULE C2114 HECU MODULE Anyone got some idea on it? Thank you in advance!

ABS Light, SRS Light, Check Engine Light, Any other lights? [ 3 Answers ]

Ok. I am writing this because I have been stumped on this question for a long time. I have a 2001 Honda Civic EX COup. I have had about every single light on my dashboard come on at DIFFERENT TIMES... My ABS LIGHTS, SRS lights, Green Flashing Key lights ( immobilizer ), Check Engine,...


View more questions Search