 |
|
| Browse | Ask | Answer | Search | Join/Login |
|
|
||||
|
How to reset my Kenmore ELITE Ultra dishwasher?
I have a Kenmore ELITE Ultra dishwasher model 66513163k701- My problem started a while back when once and a while it would just STOP on its own- The STATUS bar would blink (this would occur normally if the door was opened during a wash) but now the STATUS BAR blinks and it would stop during a cycle. Now it just won't run through anycycle. I want to reset the control panel like some older blogs on this issue but with other Kenmore models I found on the internet- HELP?
|
||||
|
||||
|
Here is what you probably need: https://dl.dropboxusercontent.com/u/...set_Codes.docx
https://dl.dropboxusercontent.com/u/...t%20codes.docx https://dl.dropboxusercontent.com/u/...Dishwasher.pdf Check the float switch and make sure it moves freely. You should hear or feel the little switch click when you raise the float, too. Check the filter and the arms. You never know what caused it to quit working. Many times it is a safety that tripped and if that is the case then you will have to fix what is causing the safety to trip. YouTube is a good source of information on any home appliance. Appliance manufacturers and good technicians post many good videos on repairing appliances on YouTube. Just type in good search terms and you will get good results. Good luck. If we can help we will if you need to write back. |
||||
|
||||
|
I tried the first "fix" and ALL the lights do come on- you say a diagnostic test should be occurring and the lights go out . The lights do not turn off on their own and I don't hear anything showing a diagnostic test is occurring. I have done this first suggested "fix" a few times, even waiting over 5 minutes or more to see if I just am not waiting long enough for the diagnostic test to run but the lights don't go off. If I press the cancel like you say (even though all the lights are on) it acts as though things are fixed, i.e.. The lights go off, I can set a wash to begin but once I press START, the status display bar lights up and no wash cycle runs... When I try the second "fix" you suggested, the exact thing occurs,- all lights come on, no noise of a diagnostic test occurs, lights stay on OVER the suggested 2 minute time, and it does the same- Status bar comes on and blinks----- HELPPPPPPP
|
||||
|
||||
|
You need to look up some fixes on YouTube, starting here: https://www.youtube.com/watch?v=sFNSUHn9_cc
https://www.youtube.com/watch?v=flzhfmIIYpM https://www.youtube.com/watch?v=zex_g2TJRl4 https://www.youtube.com/watch?v=L-bMqVb9kX0 I think the solution will be found here. Write back and let us know what you find. Make sure and go buy a good digital multimeter at Radio Shack or Home Depot. You will need it to fix anything. If it's a bad thermal fuse DO NOT cut the wires, just replace the fuse. |
||||
| Question Tools | Search this Question |
Add your answer here.
Check out some similar questions!
How do I reset my kenmore elite dishwasher
When I plug my microwave in the light comes on, fan runs and table moves. When I try to cook it says the door is open. Since this has happened evry time I try to use it I think it needs to be reset.
It stopped working mid cycle and the cleaned light is flashing the keypad does not respond It is a kenmore elite 665.16572202
My dryer was running when the power went out. I seem to remember this happening years ago... that there is a reset button somewhere. IT won't start now. Where is the reset button and how do I get to it?
I have a kenmore elite dishwasher 665.16033402 and the "clean" light stays on, I have used the posted info to reset the washer. I am able to start my washer but it only washes for about 20 minutes then the "clean" light goes on. I was wondering if anyone had the info on how to run a diagostic test...
View more questions Search
|
