Ask Experts Questions for FREE Help !
Ask
    riotbreak's Avatar
    riotbreak Posts: 2, Reputation: 1
    New Member
     
    #1

    Apr 22, 2014, 07:38 AM
    Tub drain gap
    Having an issue with tub drain plumbing. Previous homeowner was an idiot and didn't disclose much about house. Now I'm left to fix it the right way. They remodeled a bathroom and took out a portion of cast iron pipe used for the tub. Not sure if he broke it, it was corroded, or he was told to do this... He necked in a PVC pipe which reduced the diameter of the pipe by a quarter inch. This left a gap of about 3/8" between the lower shoe and tub. The only gasket I can then get in there without flexing the pipe is what I thought was the thicker (3/8") upper shoe gasket. Since the durometer of the rubber isn't very high. Tightening the drain pushes the gasket out, causing a leak. Leaving it so it isn't pushed out also has it leaking as there's not enough pressure to maintain a seal. What's the best way to go about fixing this? It would be nice if they made a taller or adjustable shoe so I could put in a smaller gasket and seal it down tight. Are there any other necks I could put in place to bridge that gap and seal it up?
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
     
    #2

    Apr 22, 2014, 08:27 AM
    He necked in a PVC
    What's :necked"?If this were my call I'd tear everything out. Convert to PVC at the cast iron and do the job correct, Let ne know what you decide, Tom
    riotbreak's Avatar
    riotbreak Posts: 2, Reputation: 1
    New Member
     
    #3

    Apr 22, 2014, 08:38 AM
    He shoved in a pvc pipe OD that fit the ID of the cast iron. So instead of having a 4.5" ID cast iron, there's a 4" ID pvc pipe pushed into it and sealed up. This reduction in the diameter of the pipe left the 3/8" gap between the shoe and tub. Can't recall from memory but not sure if the disconnected the cast iron at a junction or cut it. If he cut it, I'm going to have a harder time tearing it all out to put back together as I'm left with nothing to connect to. It's why I was wondering if there's any drain shoe taller, low angled pipe, or flexible lines that can be set in there to fix.
    talaniman's Avatar
    talaniman Posts: 54,325, Reputation: 10855
    Expert
     
    #4

    Apr 22, 2014, 08:52 AM
    I don't know if you have access beneath your tub, but you have many options to replace your tub drain or even extend the existing one.

    Tub Drain Product - Bing Images

    If in the USA, a Loews, Ace Hardware, or Home Depot can guide you to fairly easy solutions to your tub drain gap, and the leaks they have caused.

    I would remove the drain and take it with me along with the old drain measurements for correct sizing.

    Start with removing his shoe, and fitting to the original configuration.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

How do I fix the large gap at the end of my tub? [ 6 Answers ]

I installed a new tub and there is a 1" gap at the end of my tub. The plumbing is already done so I can't move it. I am going to tile and I don't know how to fill the gap. I have to install my own tub flange which I haven't done yet until I figure out this problem. I can't afford to lose an inch so...

Specifications i.e. spark plug gap,tappet gap hot & cold, air gap [ 1 Answers ]

I need these specs for a briggs & stratton Vanguard 16 hp v-twin ohv engine. Model no 303442.Thank u very much Jan

How to fill the gap between fiberglass tub/shower unit and drywall? [ 1 Answers ]

I had my fiberglass tub/shower unit refinished and there is a gap between the tub/shower unit and the drywall. I've read some info that you can use silicone caulk for gaps that are about 1/8". But some areas around the unit, the gaps are larger (between 1/4" and 1/2"). Can caulk still be used or is...

Bridging gap between new sink and old drain [ 4 Answers ]

Hey guys, I'm installing a new 49'' vanity where the sink is about 6 inches to the right of the current (old) sink. I realized that the drain pipe that's coming out of the wall does not align with the new sink. Is there a way to bridge this 6'' gap? If so, what's the best way to go about it?...


View more questions Search