Ask Experts Questions for FREE Help !
Ask
    davidjoh58's Avatar
    davidjoh58 Posts: 3, Reputation: 1
    New Member
     
    #1

    Nov 26, 2013, 01:04 PM
    Dual electrical switch
    I have to replace a dual electrical switch that was previously removed in the kitchen area. The switch is all one unit. One switch is for the dishwasher and the other one is for the garbage disposal under the sink. The switch has two brass color screws on one side and two black screws on the other side. There are two white wires and two black wires coming out of the electrical box. What is the correct way in which this four wires need to be connected to the switch.
    ma0641's Avatar
    ma0641 Posts: 15,675, Reputation: 1012
    Uber Member
     
    #2

    Nov 26, 2013, 01:31 PM
    Why a switch for the dishwasher? Those switches are both single pole units. However, with white wires it sounds like they are switch looped. Any black tape on the white wires? I would find the DW leads and wire nut them together and use the breaker for the disconnect. Then I would use a standard single pole for the disposal. If they are properly installed loops, the whites should be hot to the switches, put black tape on them.
    davidjoh58's Avatar
    davidjoh58 Posts: 3, Reputation: 1
    New Member
     
    #3

    Nov 26, 2013, 08:20 PM
    ma0641, Not sure why. I have done more investigating and found out that the actual cables have four wires: one red, one white, one black and the bare copper. The whites are twisted into a cap screw, same with the bare copper.so, which ones are hot ? The red or black? Which ones get connected to the side with the connecting tab? Please advise, thanks in advance.
    ma0641's Avatar
    ma0641 Posts: 15,675, Reputation: 1012
    Uber Member
     
    #4

    Nov 26, 2013, 08:53 PM
    Maybe both are hot. I would then surmise that you have a 12 or 14/3 with a common neutral and two breakers or one breaker with 2 hot leads. That is commonly found in an older kitchen. But, you must have an extra wire somewhere if you have more than 1 white or black. Get a test light or multi tester to determine what is hot. If one lead is hot, it would go to the side with the unbroken tab. The other side should have the tab broken off. It works that you can have 1 hot feeding 2 circuits or two hots feeding 2 circuits. White and bare are not switched , white possibly but need to be marked with black tape. BTW you posted this question 2X. Please don't do that since you will be getting many answers to the same posts. There is no need for a DW to have a switch. If you pull the bottom plate off the DW, and then remove the cover over the wire connection, you should see what color wire is for the DW.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

2 way dual dimmer switch [ 0 Answers ]

We have just fitted a 2 way dual dimmer switch to replace old one - one switch controls 6 x 50w spotlights which have own transformers - both dimmer switches are designed for up to 400w - other switch controls 4 x 50w, again with individual transformers - if we switch only the switch controlling 6...

Dual switch one light [ 4 Answers ]

I have had this set up for six years and all of a sudden one of the switches doesn't work. I have switched the switch out and the same problem. I made sure that the switch is a 3-way. If I turn one switch on and try to turn the light off with the other switch the light blinks but stays on. When I...

Swapping Dual Light Switch for Dimmer/Three Position Switch for Ceiling Fan [ 1 Answers ]

I am trying to swap out a dual switch for a switch that has a dimmer for the ceiling fan light and a three position switch to control the fan. The original wiring had white to white on switch, black to black on switch, and one black from light connected to the top switch pole and the other black...

How to wirs dual electrical switches to operate a fan and a light [ 1 Answers ]

Hi, I just purchased an exhaust fan to be installed in my bathroom. There is a light switch in the bathroom which operates the light fixture. I also purchased a dual switch to turn on and off the light and the fan seperatly. Can you tell me how to wire the dual switch correctly. Thanks ...

Troubleshoot Wiring a Dual Electrical Outlet [ 5 Answers ]

Hi all, I hope this is an easy one to answer. In my kitchen, I was replacing old electrical outlets (USA - 15a 120V). There are two specific outlets that are side-by-side. They fit in a double-sized box. Now, the outlets that I am replacing were a little bit older, and so I am a bit...


View more questions Search