Ask Experts Questions for FREE Help !
Ask
    Tilson's Avatar
    Tilson Posts: 2, Reputation: 1
    New Member
    		  
    #1

    Nov 25, 2013, 03:40 PM
    No heat
    I have a trane xb 90 the led light is flashing 5 times. I have already replaced the inducer fan, the main board, and the roll out switch. It still will not blow warm air. Any help would be great. It is getting very cold in my house for my family.
    ma0641's Avatar
    ma0641 Posts: 15,675, Reputation: 1012
    Uber Member
    		  
    #2

    Nov 25, 2013, 04:49 PM
    Why did you replace all the parts? It is unlikely they were all bad. Start with basics -what happens when thermostat calls for heat? What is the 5 blink code? Should be on the inside of the front panel.Does ignitor light? Is it very bright?-should be a yellow heat. Have you cleaned or replaced the flame sensor? Reset all limit switched? -pushed the red buttons? Tested the high limit sensor? -usually a small black square item with 2 wires, located on main plenum.
    Tilson's Avatar
    Tilson Posts: 2, Reputation: 1
    New Member
    		  
    #3

    Nov 25, 2013, 05:00 PM
    The 5 blink code says it's the roll out sensor. I replaced the board because after a hvac tech. came over we followed allt he lines and after unpluging the wire harness and pluging it back in the ignitor worked two times ran a full cycle and then stopped again. I figured the board was going. The first board was flashing six times and that meens a bad ground. Which was not the case. Now the new one flashes 5 times and I replaced the roll out switch cause that's what it indicated. Still no heat. Everything else is working fine.
    ma0641's Avatar
    ma0641 Posts: 15,675, Reputation: 1012
    Uber Member
    		  
    #4

    Nov 25, 2013, 05:33 PM
    Quote Originally Posted by Tilson View Post
    The 5 blink code says it's the roll out sensor. I replaced the board because after a hvac tech. came over we followed allt he lines and after unpluging the wire harness and pluging it back in the ignitor worked two times ran a full cycle and then stopped again. I figured the board was going. The first board was flashing six times and that meens a bad ground. Which was not the case. Now the new one flashes 5 times and I replaced the roll out switch cause that's what it indicated. Still no heat. Everything else is working fine.
    So the inducer fan comes on? Does ignitor try to light? Rollout switch problem is usually post ignition. Make sure the pressure sensor is OK and I would also test the high limit sensor.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Heat pump never turns on, handler blows continuous with no heat except with AUX heat [ 2 Answers ]

10 year old Rheem air handler RHBA-21J8MFCA, 1/3HP, 2.8A. New WeSt Columbia, SC 29170, Model 2HP13L48P-1B, HCFC-22, 4TON. Installed new out of box iN July and AC working splendidly but start-up is "violent" and loud. Installer says I need some sort of "start-up kit". I put off as had planned...

Kenmore dryer won't heat.changed the heat element+thermal fuse.still won't heat [ 1 Answers ]

Kenmore dryer(110.96582100) is 15 years old. Worked great until it stopped heating. Actually it started taking longer and longer to dry the clothes. But now it won't heat at all. I've changed the heating element and thermal fuse. Could it be the thermistor or high limit thermostat? Don't want...

Heat Pump blows 5amp fuse when switching between defrost & back to heat. Them Heat work [ 3 Answers ]

I have a Carrier Heat Pump System. It’s about 5 years old and has functioned OK until this Christmas Eve. One problem is the condensing unit is not kicking back on after it goes into defrost mode. I found a 5AMP fuse blown in the attic unit and once replaced it functioned. At least for a day or two...

Carrier Hvac heat pump with aux/em heat- NO AUX HEAT [ 1 Answers ]

I have tried to install Honeywell 7500d thermostat. I get heat pump heat but no emergency heat although the termostate is calling for it. The installation manual says to see authorized agent if I have a dual 0/b on existing thermostat and another wire is attached to common. As of now, I have ...

View more questions Search