Ask Experts Questions for FREE Help !
Ask
    KC2112's Avatar
    KC2112 Posts: 3, Reputation: 1
    New Member
     
    #1

    Oct 25, 2013, 11:32 AM
    Lights flickering and low power to appliances
    I have a serious problem with my lights flickering. It does this every time an appliance runs, furnace kicks on, dryer or dishwasher running, microwave running, etc. The microwave will run fine for like 5 seconds then all of a sudden it just will seem to lose power and gets weak. Fans and hair dryers also lose power. I called the power company and they came and said everything was fine on their side. They did say that the cable that runs from the top of my house into the meter had several cracks in it. He wouldn't give me an answer when I asked if that could be causing my issues. He just shrugged his shoulders. I checked my breaker box and all the connections seemed fine. I just have no idea what to do. Does anyone have any advice on what to do?
    KC2112's Avatar
    KC2112 Posts: 3, Reputation: 1
    New Member
     
    #2

    Oct 25, 2013, 11:34 AM
    Sorry I have 200 amp service. My home is 30 years old. Thanks
    donf's Avatar
    donf Posts: 5,679, Reputation: 582
    Printers & Electronics Expert
     
    #3

    Oct 25, 2013, 12:35 PM
    You need to call your utility company and have them verify that they are delivering the proper amount of power to your residence.

    There are several possibilities not the least of which is the main service panelboard is failing. But if the meter base or cable from the transformer are compromised, then they need to be corrected first.
    hfcarson's Avatar
    hfcarson Posts: 1,003, Reputation: 49
    Ultra Member
     
    #4

    Oct 25, 2013, 12:39 PM
    You need a smart electrician for this one. Frequently it's a loose connection although finding it could take a while. You can make guesses about this forever, so hire a professional.
    hkstroud's Avatar
    hkstroud Posts: 11,929, Reputation: 899
    Home Improvement & Construction Expert
     
    #5

    Oct 25, 2013, 12:39 PM
    Could be a loose or bad connection in the incoming neutral to the breaker panel. Not something for DIYer to play around with. Call a licensed and qualified electrician. If it does turn out to be on the power company's side you will need the electrician's diagnosis to prove it.

    Call an electrician.
    stanfortyman's Avatar
    stanfortyman Posts: 5,598, Reputation: 279
    Electrical & Lighting Expert
     
    #6

    Oct 26, 2013, 05:18 AM
    You need a smart electrician for this one. Frequently it's a loose connection although finding it could take a while. You can make guesses about this forever, so hire a professional.
    This is your only answer. For real.
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
     
    #7

    Oct 26, 2013, 07:59 AM
    Basically the Electrician would check voltage out of Meter can, in and out of Disconnect, then In on Panel, then Panel Breakers, 99% of the time it is a Bad Connection, A bad Breaker(s), or a Burn Buss(what the breaker plugs onto. Introducing the Load with the Meter attached will expose the problem.
    Just guessing, If the Lights don't get Brighter, Then it is more likey NOT to be the Neutral.
    tableclocks's Avatar
    tableclocks Posts: 432, Reputation: 2
    Full Member
     
    #8

    Nov 2, 2013, 02:39 PM
    I have a similar problem.. I traced mine to a loose main braker where it connects to the buzz bar...
    donf's Avatar
    donf Posts: 5,679, Reputation: 582
    Printers & Electronics Expert
     
    #9

    Nov 3, 2013, 08:41 AM
    Tableclocks,

    Did you mean to say, "Bus" bar? If you have not tried to repair this failure, then I strongly suggest that you get a licensed electrician to fix this for you.

    The only safe way make the repair is to pull your meter and more than likely your POCO will not allow a homeowner to do that.
    tableclocks's Avatar
    tableclocks Posts: 432, Reputation: 2
    Full Member
     
    #10

    Nov 3, 2013, 09:19 AM
    OK... thank you for correcting me... its a bus bar...
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
     
    #11

    Nov 5, 2013, 05:36 AM
    Buss Bar.
    KC2112's Avatar
    KC2112 Posts: 3, Reputation: 1
    New Member
     
    #12

    Nov 13, 2013, 03:54 PM
    Just wanted to thank everyone for your replies. Luckily my daughter's boyfriends father just happens to be an electrician. He came out and noticed right away what my problem was. The main service cable coming into the house had large cracks in the sheathing. He guaranteed me that was the problem. He agreed to help me change it and do a complete service upgrade. I called the power company to have the service disconnected. The technician came and disconnected our service. He was shocked when he pulled the meter from the meter box. The neutral wire was completely corroded. The aluminum looked like white powder and was disintegrated in spots. We installed new service cable using 2/0 copper wire, and installed a conduit mast to house the wiring. We also installed a new meter box and a 40 circuit Square D panel. My electric is now back to normal. Also since we used copper and conduit, I'll never have that issue again to worry about! Again, thanks for the replies!
    hfcarson's Avatar
    hfcarson Posts: 1,003, Reputation: 49
    Ultra Member
     
    #13

    Nov 14, 2013, 05:28 AM
    And thank you for giving us a description of the actual problem and repair...
    (knew it was neutral)
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
     
    #14

    Nov 15, 2013, 08:17 AM
    Don't hear a lot of good stories with aluminum.
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
     
    #15

    Nov 15, 2013, 08:20 AM
    When I said Buss Bar, I was correcting the spelling from Buz, Bus, to Buss.
    Since it was the Neutral, I bet some lights got brighter when something else was turned on.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Flickering lights [ 2 Answers ]

I have floresscent lights that flicker when other people have their lights on. When there are only my lights or 1 or 2 other lights on they work fine. Any suggestions as to how to keep them from flicker when there are other lights on. They are plugged into a screw in light socket up on the ceiling.

Flickering lights? [ 3 Answers ]

Have a very brief & slight flickering of incandescent lights (on different circuits) every 45 seconds. Just started doing this during last week. Can't tell if the lights get brighter or dimmer - it happens so fast. No other electrical devices turned on that might cause flickering. Have an old...

Flickering lights [ 2 Answers ]

The agitation cycle of my washing machine causes all my lights to flicker

Flickering lights [ 1 Answers ]

:mad: i have some lights that are flickering in the down stairs bath and hall and a small computer room what could be the problem? I think it could be a week braker, or a bad connection. What do you think. Thanks for any help.

Flickering lights [ 37 Answers ]

Bigg oops I thought I double posted the question some how and edited/lost the origonal Dangit will try to recompose it Issue of dimming lights, brightening of lights, constant flickering. All these would be a lot worse of a flicker when it is night time or windy out, but still quite often in...


View more questions Search