Ask Experts Questions for FREE Help !
Ask
    Rob348's Avatar
    Rob348 Posts: 4, Reputation: 1
    New Member
    		  
    #1

    Oct 8, 2013, 01:49 PM
    Goodman manufacturing gas furnace issues
    We had a power outage not too long ago and noticed that our blower began to run continuously, even with it shut off from the thermostat. The glow igniter glows really hot but nothing else seems to happen. What could be wrong with it? I've read a lot of answers, but with the igniter working I'm not sure if it's the limit/pressure switch or not. Any ideas would be greatly appreciated. Also... the LED indicator stays on, suggesting everything is fine. =/ Obviously something isn't right.
    Grady White's Avatar
    Grady White Posts: 1,417, Reputation: 59
    Ultra Member
    		  
    #2

    Oct 8, 2013, 07:41 PM
    Please provide us with the model number of the furnace.
    Rob348's Avatar
    Rob348 Posts: 4, Reputation: 1
    New Member
    		  
    #3

    Oct 9, 2013, 07:47 PM
    Gmpn080-4
    Rob348's Avatar
    Rob348 Posts: 4, Reputation: 1
    New Member
    		  
    #4

    Oct 9, 2013, 07:50 PM
    We ordered another circuit board just in case that may be the issue. We've had a few power outages over the summer. Any help would be greatly appreciated, this is our first time working on a gas furnace.
    Rob348's Avatar
    Rob348 Posts: 4, Reputation: 1
    New Member
    		  
    #5

    Oct 9, 2013, 07:57 PM
    Another thing, I don't know if I can get help with or not, is that the igniter glows really hot and I've noticed the first two burners, are covered in soot as if they've been getting too hot and the cover also, has shown signs that the burners are too hot on that side. What could be the malfunction in that?
    Grady White's Avatar
    Grady White Posts: 1,417, Reputation: 59
    Ultra Member
    		  
    #6

    Oct 10, 2013, 01:35 PM
    With the soot being present, I suggest you call a local professional. There is a strong probability there is a major internal problem with the furnace.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Goodman Furnace issues [ 4 Answers ]

I have a Goodman furnace(GDS80453ANA) in my rental house (6 yrs old). It runs great and has for the 6 yrs. PROBLEM: My house is 900 sqft and has 6 registers. The air coming out of each register is superb, BUT, its only luke warm. ALSO, the furnace runs all the time. I'm guessing it might be...

I have a goodman GDT090-4A gas furnace. The igniter will ignite the gas and the gas w [ 2 Answers ]

The igniter will ignite the gas, and the gas will run for a second or a few seconds and will then cut off. It will continue to cycle like this until it finally will stay on but at times will take forever.

Troubleshooting goodman manufacturing furnace? [ 1 Answers ]

I have a Goodman GMP furnace which now will not come on. When I unplug the unit and plug it back in, it tries to start for a split second and then just quietly hums. Any thoughts?

Goodman gas furnace installed 3 years ago, no issues until now [ 1 Answers ]

Goodman Gas furnace GDS81155CXB. When we went to test furnace at end of October, the motor spins fine, then we get 2 blinks followed by repeating 3 blinks on the error light. I am no HVAC guru by any means. Any help would be greatly appreciated as I don't have big bucks to shell out.

Goodman Furnace issues [ 0 Answers ]

So I have a Goodman GMPN060-3 REV 3 furnace and it works fine for a while then I check it and the red status light starts to blink rapidly. It says it says to check the twinning and Polarity of the wires. I checked them a replaced the Thermostat and it worked for about a hour then shut off and...

View more questions Search