Ask Experts Questions for FREE Help !
Ask
    Samantha9311's Avatar
    Samantha9311 Posts: 1, Reputation: 1
    New Member
     
    #1

    Oct 7, 2013, 12:43 PM
    My whirlpool cabrio dryer
    My dryer stays on the sensing light and want turn on as in dry my clothes.it want turn.
    drtom4444's Avatar
    drtom4444 Posts: 3,282, Reputation: 145
    Ultra Member
     
    #2

    Oct 7, 2013, 11:47 PM
    It sounds like you have a broken belt. Since it has run long enough to wear out the belt it needs cleaning, too. You need to totally tear it down and scrape out and wash all of the parts except the motor, which you vacuum out. You can go to YouTube to see videos on how to take it apart, but do a very good job or it will fail again quickly. Get some white lithium grease and grease any bearings you find. You need to clean out a drier every two years, at least, according to the manuals.
    Look at: How to clean your clothes dryer. How to make it hot again. - YouTube to see how to tear it down. Also: Mr. Appliance Tips: How to Clean Your Dryer - YouTube ; Cleaning a Dryer Vent and Lint Trap - YouTube
    Electric Clothes Dryers
    Whirlpool Dryer Model LE5800XSW3 Wiring Diagram | Dryer Repair | Fixitnow.com Samurai Appliance Repair Man
    https://dl.dropboxusercontent.com/u/...e%20Manual.pdf
    The job is very easy for anyone to do. Just get it out into your garage or somewhere you will have plenty of space. Pop the top and unplug the wiring harness, then you can see where the screws are that hold on the front. You will need to unplug the door switch. You should lay it on its back to make it easier to work on before pulling off front. Make sure to clean it very well and don't miss the duct on the door going to filter or the other ducts in the rear, and the blower wheel and housing which is very, very important. A clog of cement-like lint build up can hide anywhere. Don't be afraid to take apart anything to be able to look inside and clean it. One missed place will necessitate doing all this again and no one wants to redo something. Grease all support rollers with white lithium grease and reassemble and you have a new dryer.
    Here are some manuals: https://dl.dropboxusercontent.com/u/...l%20Dryers.zip
    https://dl.dropboxusercontent.com/u/...e%20Manual.pdf
    You should check the safeties out before reassembling it to make sure you have not also blown one open.
    See:https://dl.dropboxusercontent.com/u/...e%20Manual.pdf

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Whirlpool Cabrio Dryer [ 16 Answers ]

We just had a new Whirlpool Cabrio washer and dryer (electric) installed today. I dried some towels and noticed an unusually loud humming and vibrating sound. I wouldn't expect this from a product with a "very good" noise rating rated by consumer reports. It's much louder than my old 17 year old...

Whirlpool Cabrio Dryer [ 17 Answers ]

We purchased new Whirlpool Cabrio Washer & Dryer set from Sears. The washer has worked fine, but the dryer has not. The dryer was delivered and had a small dent on the front of the door. When we put clothes in the dryer and start it, the dryer is extremely loud. It sometimes has a piercing...

Whirlpool cabrio dryer [ 1 Answers ]

I have a Whirlpool Cabrio Dryer. It is approx. 3 yrs old. I have noticed that when I put clothes in to dry and hit start it has the digital time displayed for a minute or so then a message appears saying AF and it starts flashing. I have to hit the clear button and it goes back to the...

Whirlpool Cabrio Dryer [ 2 Answers ]

A sponge fell down the opening of the "lint catcher" while it was out because I was removing back up lint. While the lint catcher fits back in, I do not know if it is dangerous to leave the sponge down there, and if so, I do not know how to get it out--tried with a hanger but couldn't catch on to...


View more questions Search