Ask Experts Questions for FREE Help !
Ask
    tctrekker's Avatar
    tctrekker Posts: 1, Reputation: 1
    New Member
     
    #1

    Apr 14, 2013, 07:20 AM
    Washer need a starter push to spin!
    The agitation cycles seem to operate properly but when it comes to the spin cycles the water drains then the washer motor sounds like it is spinning but when you open the lid the motor brakes but the drum was never spinning. I depress the lid switch and give the drum a starter push and will then spin up to speed until the next cycle starts.
    JudyKayTee's Avatar
    JudyKayTee Posts: 46,503, Reputation: 4600
    Uber Member
     
    #2

    Apr 14, 2013, 08:33 AM
    When my washer did this the belt needed to be replaced
    rcaldwell's Avatar
    rcaldwell Posts: 39, Reputation: 2
    Junior Member
     
    #3

    Apr 14, 2013, 08:38 AM
    Hi, in regards to the washer not spinning, I have seen this before and it's not uncommon problem in the appliance repair world. I've been in the repair biz in Boise for 30 years. So, here we go, you could have a couple of problems.
    The clutch could be worn. If it is, it's not gripping the washer spin tube enough. Another is a piece of clothing stuck between the outer and inner basket, giving drag to the spin tube and clutch. The third is the spin tube itself, which encompasses the brake. The brakes could be dragging. I've seen this often. Oh, one more, the motor could be weak. I haven't seen this very often but it's a real possibility. Hope this helps, I know it's a lot. The cost on replacing the spin tube is 300 plus, from a pro. You may want to invest in another washer though, if it's old.

    >advertising removed<
    JudyKayTee's Avatar
    JudyKayTee Posts: 46,503, Reputation: 4600
    Uber Member
     
    #4

    Apr 14, 2013, 09:39 AM
    Really great, comprehensive info - but the site advertising your company is not allowed. Wish it were, because I have my own company and have posted over 40,000 times... but it's not allowed.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Direct drive washer won't spin-rotate tube 4 inches and it will spin [ 1 Answers ]

I have a direct drive washer. Have checked the motor coupler. Replaced the clutch. When it gets to the spin cycle it won't spin. If you open the lid and rotate the tub counterclockwise about 4 inches then close the lid it will spin. What could be wrong?

Whirlpool washer, agitator works, but during the spin cycle it doesn't spin [ 1 Answers ]

I have a whirlpool washer, I replaced the outer tub and the drive block, but it now doesn't spin. It drains the water, I can hear the motor come on, and feel the vibration . The switch is fine. I looked at the couple, but did not take it apart. The clutch looked fine, sanded the pads and case....

Kenmore Elite Washer does not spin in slow spin cycle until lid is opened and closed [ 0 Answers ]

I have a Kenmore Elite Top Loading Washer, Model 110.24952300. When the washer goes to the spin cycle, it does not spin in the first spin cycle. It does this in the slow spin cycle that precedes the main spin cycle. When it cycles to the regular spin cycle, it does spin properly. I found that...

Kenmore washer 70 series humming at spin cycle - won't spin [ 4 Answers ]

RE: kenmore 70 series model 110.20712990 Type 111 top load washer. Won't spin. Humming noise and a little burning/hot smell when supposed to be spinning. Bypassing the lid switch did not correct the problem. Changed out the motor coupling with no luck... still a humming noise but no smell.

Push Mower Starter Cord Replacement [ 1 Answers ]

John Deere Push Mower-Starter Cord Broke What are the replacement steps?


View more questions Search