Ask Experts Questions for FREE Help !
Ask
    Davep's Avatar
    Davep Posts: 2, Reputation: 1
    New Member
     
    #1

    Dec 30, 2012, 05:52 PM
    4 supply lines run to tub?
    I was doing some work on my tub and noticed they ran 2 cold and 2 hot supply lines (copper) to the tub,

    The 2 cold lines come in vertically and then connect with a 90 degree fitting and then run on up to the mixer.

    The hot lines do this too.

    Is this normal I've never seen this.

    It is not giving me any trouble, just wondering why it is done this way.
    massplumber2008's Avatar
    massplumber2008 Posts: 12,832, Reputation: 1212
    Senior Plumbing Expert
     
    #2

    Dec 30, 2012, 06:00 PM
    Hi Dave

    It is NOT normal, for sure, but they may have run extra water lines during a remodel to accommodate a higher volume shower valve.

    How many shower heads/body sprays at the tub/shower?

    Do you have a separate tub valve and a separate shower valve?

    Let us know, OK?

    Mark
    Davep's Avatar
    Davep Posts: 2, Reputation: 1
    New Member
     
    #3

    Dec 30, 2012, 07:15 PM
    Mark, thanks for the reply. There is only one shower head and one faucet. The faucet and shower head connect and use a diverter in the spout.

    The pipes come up through the slab so I assume they are original, house was built in 1971. Could it be feeding another fixture like the bathroom sink or the toilet?
    massplumber2008's Avatar
    massplumber2008 Posts: 12,832, Reputation: 1212
    Senior Plumbing Expert
     
    #4

    Dec 31, 2012, 07:50 AM
    Yeah.. seems reasonable. Seeing that you can't have solder fittings underground they must have come above ground and then run lines underground over to the other fixtures... ;)
    afaroo's Avatar
    afaroo Posts: 4,006, Reputation: 251
    Ultra Member
     
    #5

    Jan 1, 2013, 04:07 AM
    I agree with Mark, if you don't have a problem with just leave it as it is, Thanks.

    John
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
     
    #6

    Jan 1, 2013, 08:17 AM
    If you're on a slab the lines could be a manifold takeoff. Happy new year, Tom

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Clog in water supply lines after replacing section at main municipal supply... [ 1 Answers ]

I had an exposed water supply line that ran from the city inlet to my house. It was old and rusty so we decided to replace it with a PEX pvc piping. It's the same dia. (3/4") and we replace the one 90 elbow with a 45 instead. When we turned the water back on, it had no pressure, and after my...

Connecting Copper Supply Lines to Brass Supply Lines [ 3 Answers ]

I have just started remodeling my kitchen and am looking to move my kitchen sink further down the wall. The kitchen is completely gutted at this point. The supply lines in my house are all brass. I'm looking to stem off the brass lines using copper tubing. Is it possible to cut the brass supply...

Clawfoot tub solution for wall supply lines instead of floor [ 4 Answers ]

We are finishing our basement and in the bathroom we are putting in a clawfoot tub. My husband put the supply valves in the wall because he was afraid of freezing in the floor. But because of this we cannot find any supply lines that come from the wall they all come from the floor. Is there...

Supply lines [ 3 Answers ]

Just a question regarding supply lines. I'm pretty sure I'm going with CPVC for the supply side. Planned on making a 3/4" or 1" manifold then branching off that with 3/4" for the main lines with 1/2" for all my fixtures. I have to supply 2 full baths, 1 kitchen and to outside spickets. Can I...

Can I run Supply lines in outside wall [ 2 Answers ]

I live in NJ and am remodeling a bath. Can I run my supply lines to the shower in an outside wall? If so any recommendations or hints concerning this?


View more questions Search