 |
|
|
 |
New Member
|
|
Nov 9, 2012, 08:47 AM
|
|
Help fitting a new ceiling light
Hi, I bought a new ceiling light which has the normal, neutral, live and earth connections. I have just taken down the old light bulb connection and I am totally confused.
I have three electrical cables coming out of the ceiling and I am looking at three earth wires, two red wires (old live) two black wires and a black wire which someone has put a bit of red insulation around it.
I can't seem to get the connection right, it's either constantly on and completely ignoring the switch on the wall or not working at all.
I am a major newbie and can't even remember how it was connected to the old bulb!
Help me please
Oh and I think it might be somehow connected to the light at the top of the stairs...
|
|
 |
Uber Member
|
|
Nov 9, 2012, 08:57 AM
|
|
Sounds like you have a switch loop, two wires in one cable coming from a switch, live power needs to connect to one wire, and the other will connect the live wire of the fixture.
Blue wire on the fixture should all be connected and is the neutral.
You need to figure out which wire is live. I suspect one cable connects to live and neutral and feeds something else.
I hope this helps.
|
|
 |
New Member
|
|
Nov 9, 2012, 09:14 AM
|
|
Thank you so much for taking the time to help me, can I explain at bit more what I'm looking at coming out of the ceiling...
I have three big electrical cables coming out the ceiling.
One has a red wire, a black wire and an earth.
One has only a black wire and an earth
One has a red wire, an earth and a black wire (which someone has put a red loop of wire on)
I have tried loads of variations but can only seem to get either constant on or not working...
|
|
 |
New Member
|
|
Nov 9, 2012, 10:34 AM
|
|
Thanks so much, thanks to you saying swithc loop, I looked up the diagram and it would appear this is what it is, the black wire with the red flex on signifies the switch wire, (learn something new every day!) I can now trun the light on and off but the dimmer doesn't work, (it was working before I started messing about!)
Any thoughts?
|
|
 |
Uber Member
|
|
Nov 9, 2012, 02:02 PM
|
|
I did the best I could , the color code you have tells me your not in North America, and I don't know others codes and methods, so much.
Sounds like you have managed.
If you were doing any connecting of wires while energized, or if there was a short circuit, the dimmer easily could had been damaged.
Be sure all connections are tight.
Never connect dimmers, esp the electronic ones, live.
|
|
Question Tools |
Search this Question |
|
|
Add your answer here.
Check out some similar questions!
Fitting new Kitchen Light
[ 3 Answers ]
Hello all,
I am trying to replace the old halogen spotlight bar light fitting in my kitchen with an new one.
Foolishly I didn't pay much attention to the wiring of the old one before I removed it, "3 wires = poss, neut and earth....." or so I thought.
However on more investigation it...
Light Fitting Problem
[ 1 Answers ]
Hi, I have just installed a new light fitting and depending on how I wire it up it is either not on or on all the time! What am I doing wrong?
Fluorescent light fitting cover
[ 1 Answers ]
Is it possible to replace only the plastic cover for a fluorescent light fitting (bathroom) rather than replacing the whole lot that would require an electrician?
Fitting new ceiling bathroom light in OLD house
[ 4 Answers ]
So far we've established black = neutral, red = live, green = earth. We know which 'hole' the relevant wires go in thanks to a useful wiring diagram. What we cannot fathom is what to do with the seemingly spare neutral wire. We have 3 of them with only 2 holes to put them in?
View more questions
Search
|