Ask Experts Questions for FREE Help !
Ask
    epaz22's Avatar
    epaz22 Posts: 2, Reputation: 1
    New Member
     
    #1

    Oct 18, 2012, 02:05 AM
    Fitting new Kitchen Light
    Hello all,

    I am trying to replace the old halogen spotlight bar light fitting in my kitchen with an new one.

    Foolishly I didn't pay much attention to the wiring of the old one before I removed it, "3 wires = poss, neut and earth....." or so I thought.

    However on more investigation it would appear that I have 1 constant live, 1 switched live, and (im guessing) neautral.

    The old fitting only had 2 terminals for the connection, 2 of the wires were connected to 1 terminal and the othe was connected to the other on its own.

    The new fitting has a lot of terminals grouped - poss, neut, earth, loop.

    Any ideas on what wire goes where?

    Also since disconnecting the old fitting the bathroom and utility room lights no longer work.

    (all 3 of these wires come out of the ceiling seperatly and are all grey insulated solid copper wire.)

    Any help gratefully received

    Thank you

    Edward
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
     
    #2

    Oct 18, 2012, 07:05 AM
    Can you provide a picture?
    Do each of the 3 grey "wires" have 3 conductors?
    epaz22's Avatar
    epaz22 Posts: 2, Reputation: 1
    New Member
     
    #3

    Oct 18, 2012, 10:58 AM


    Ok - so bit more info for you guys

    Done some investigation in the light of day.
    As you can see the error in my post was that all the wires are grey - they are but with secondary insulation under-
    So we have wires 1, 3 - both grey and wire 2 red (also has uninsulated wire running under outer grey insulation - hello earth!)

    Wire 3 constant live - live when light switch is on or off
    Wire 2 switched live - is only live when light switch is on
    Wire 1 neutral - is never live with light switch on or off



    Wiring for new fitting

    So what should I put where?

    I think I can guess but...
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
     
    #4

    Oct 19, 2012, 07:33 AM
    Looks Dangerous, if in an attic and accessible I would redo safely.

    As far as the problem, The switced leg would go to the hot on that fixture, and the other 2 MAY? Be neutrals.
    Try tuning off the Bath and Utility lights and see if voltage goes away on one of the conductors, if so, the 2 were most likely connected as the neutral.
    For a test, Identify the switched leg with yellow or other tape. Then turn off power, and connect the switched leg to the line and the remaining 2 to the neutral. Turn breaker back on. There is greater odds that it will work, as opposed to triping the beaker, or blowing the fuse. Be sure the fuse or Breaker will protect the wire, 15 Amp for #14, and 20 amp for #12.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Funny smell coming from light fitting [ 5 Answers ]

Hi I am very confused, there has been an awful smell, similar to fish coming from the light fitting in one of my bedrooms, what could it be?

Light Fitting Problem [ 1 Answers ]

Hi, I have just installed a new light fitting and depending on how I wire it up it is either not on or on all the time! What am I doing wrong?

Fitting a fluorescent strip light [ 3 Answers ]

Hi guys, Basically my set up is, 3 wires coming out of the ceiling, each wire has its own blue, brown and pure copper core (no flex), I assume these are neutral, live and earth. Also 2 of the brown wires are connected into one of those grey electrical connectors/joiners with the pins to...

Changing a ceiling light fitting [ 2 Answers ]

I am trying to change a light fitting in our bedroom but I'm struggling as there are 4 red wires and two black?

Fluorescent light fitting cover [ 1 Answers ]

Is it possible to replace only the plastic cover for a fluorescent light fitting (bathroom) rather than replacing the whole lot that would require an electrician?


View more questions Search