Ask Experts Questions for FREE Help !
Ask
    Kyle_in_rure's Avatar
    Kyle_in_rure Posts: 341, Reputation: 10
    Full Member
     
    #1

    Oct 10, 2012, 12:26 PM
    Hotpoint Window A/C Compressor
    We have a 20 amp 240 volt (split phase) Hotpoint Window A/C installed on our farm. The manufacturing date is 1979, but I have no other information on it. Recently when I turned it on, the fan started fine, but the compressor failed to start and was making a grinding noise, causing the power to surge. The breaker then tripped. I know about electrical and motors but know little about air conditioners. The unit only gets used a few times a year. What should I do?
    ma0641's Avatar
    ma0641 Posts: 15,675, Reputation: 1012
    Uber Member
     
    #2

    Oct 10, 2012, 02:50 PM
    It's 33 years old! A newer unit will probably pay for itself over 1-2 years due to the higher efficiency. I'd replace it.
    mygirlsdad77's Avatar
    mygirlsdad77 Posts: 5,713, Reputation: 339
    Plumbing Expert
     
    #3

    Oct 10, 2012, 04:36 PM
    Before I replaced it, I would check/change the compressor capacitor. Usually only run around ten bucks. However, it may be wise to put that ten bucks towards a new unit as mao641 suggested. At that age, there is a good chance the compressor is toast, and if it isn't, something else is surely soon to go.
    Kyle_in_rure's Avatar
    Kyle_in_rure Posts: 341, Reputation: 10
    Full Member
     
    #4

    Oct 10, 2012, 07:36 PM
    I was wondering what would cause the grinding noise and failure to start. The only reason I'm hesitant to replace it is we only use it maybe 3 weeks (max) out of the year, otherwise we just run the fan to circulate air.
    wmproop's Avatar
    wmproop Posts: 3,749, Reputation: 91
    Ultra Member
     
    #5

    Oct 11, 2012, 05:31 AM
    To the scrap yard it should go,, 33 years, its not worth the 10 bucks

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Lg ac window unit compressor staying on [ 3 Answers ]

My lg window ac units compressor is staying on even when display is off. The only way to shut it off is to unplug it. I disconnected the display board from the pcb board and the compressor still ran Im thinking about replacecing the pcb board but I was wondering if the capacitor is only a start or...

Why does the compressor on a window ac unit stay on when turned off? [ 1 Answers ]

My window unit compressor stays on when turned off

Can I connect a compressor that is window type aircon to my car and used 134a or can [ 2 Answers ]

I wan to make changes to my aircon of my car I will use a compressor from a window type aircon and used r 22 to the system is this going to work.

Maytag window a/c unit.when compressor kicks on fan runs backwards [ 1 Answers ]

Can anyone tell me why my Matag window a/c fan motor runs backwards when compressor kicks on? When the compressor shuts off the fan slows down and then runs the right way.Unit is about 4 years old and still runs cool, but amount of cold air that comes out now has been deminished when comp. kicks...

Heat pump outdoor fan runs not compressor voltage at compressor good. New compressor [ 1 Answers ]

Have a new compressor. Just replaced fan runs compressor does not, have voltage at the compressor plug? What could stop from coming on high side and low side equal at 100psig.


View more questions Search