Ask Experts Questions for FREE Help !
Ask
    JohnRoss69's Avatar
    JohnRoss69 Posts: 3, Reputation: 1
    New Member
     
    #1

    Sep 28, 2012, 01:51 PM
    Air Handler Blower runs for 20 seconds then stops for 3 seconds
    Tempstar Air Handler FXM4X4800A1 Installed 09/2010.
    Tempstar Heat Pump TXH548GKA100 Installed 09/2010
    A/C system controlled by Carrier Comfort Zone 4 Zone System installed in 1992.

    When AC comes on the Air Handler Blower runs for about 20 seconds then stops for 3 seconds then runs for about 20 seconds. This happens the entire time the system is running.

    I turned the thermostats Heat Switch Off & the Cool Switch Off and turned the fan Switch from AUTO to ON & the blower motor did the same thing, blower runs for about 20 seconds then stops for 3 seconds then runs for about 20 seconds.

    NO burning or other smells coming from the AC unit.

    I opened the air handler service panel and this unit DOES NOT have a run capacitor.

    The blower wheel (squirrel cage) spins freely and is quiet.

    The evaporators metal housing has what appears to be rust on the side under each of the copper lines where it comes out of the evaporator and goes back in. Not sure if this is normal for a 24 month old unit?

    The evaporator coils fins are clean.

    The system is running fine & the house is cool. All three filters have been replaced.
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
     
    #2

    Sep 28, 2012, 05:01 PM
    Carrier Comfort Zone 4 Zone System installed in 1992.

    It is probably the Carrier Zone system causing the problem. Bypass the zone system if you can and see what it does. It is probably some kind of a time delay in the control system somewhere that has lost its setting or a sensor for cooling control.
    JohnRoss69's Avatar
    JohnRoss69 Posts: 3, Reputation: 1
    New Member
     
    #3

    Sep 28, 2012, 05:28 PM
    HVAC1000,

    Thank you for responding.

    It looks by your Avatar you've traveled to the east?
    JohnRoss69's Avatar
    JohnRoss69 Posts: 3, Reputation: 1
    New Member
     
    #4

    Apr 29, 2013, 10:05 AM
    I just found a VERY Honest HVAC repair company that quickly diagnosed this problem today 04/29/13.

    A component inside the X-13 blower assembly motor was bad. The technician told me Tempstar has had a lot of problems with the X-13 motor and he has replaced a lot of them.

    AC is now up and running without shutting off every 20 seconds as it did before.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

The blower comes on for 2-3 seconds stops and repeats the same action. [ 1 Answers ]

The igniter don't kick in either ?

Bryant plus 355MAV, Furnace runs a few seconds then stops, pressure switch calibratio [ 8 Answers ]

Bryant plus 355MAV, Furnace runs a few seconds then stops, pressure switch calibration fault code, 4 yellow 3 green. I checked the intake and exhaust pipes, seem clear... don't know what to do from here without screwing something up.

My top loading kenmore washer runs for 10 seconds and stops for 5 minutes and runs ag [ 0 Answers ]

My top loading kenmore washer runs for 10 seconds and stops for 5 minutes and runs again for 10 seconds.

Thermostat runs for a few seconds stops and starts again? [ 1 Answers ]

Newly installed honeywell RTH230B thermostat; when the heat clicks on the fan runs for about 10 seconds, stops for a bit and then restarts and heats the house. This did not happen with the old thermostat.

Water runs for 30 seconds and then stops running [ 8 Answers ]

For 5 days now whenever we turn on a faucet the water runs as expected for maybe 30 seconds and then just quits running. This is happening in the kitchen, shower, washing machine, basically everywhere in the house. We live outside the city limits and just recently started receiving 'city' water...


View more questions Search