Ask Experts Questions for FREE Help !
Ask
    genospin4yr's Avatar
    genospin4yr Posts: 2, Reputation: 1
    New Member
    		  
    #1

    Aug 26, 2012, 08:49 PM
    GE Washer No Spin in Spin Cycle
    My GE Washer will not spin in the spin cycle.
    The lid switch is working as there are other cycles that I can open the lid and it will stop operating, close and it begins again.
    It does agitate.
    I removed both ends of tub for water level switch. I can blow back into tube. I can blow and her click in switch. The switch also seems to work correctly filling at proper levels.
    In rinse cycle I can see it agitate which demonstrates belt is working. The drum will move or spin about a foot a couple of times each way. I hear a loud click when it kicks in to grab the tube (if that is what you call it). It just never starts to spin fast all the way around.
    I read something about reseting board by unplugging a minute and then after plug in open and close door 12 times real fast. Seemed to have no effect. The green light over motor flashes constant fairly quickly.
    drtom4444's Avatar
    drtom4444 Posts: 3,282, Reputation: 145
    Ultra Member
    		  
    #2

    Aug 27, 2012, 12:31 PM
    It sounds like the spin solenoid, but you will have to test it with a meter. Here are the manuals you will need: https://dl.dropbox.com/u/8010163/GE%...%20Manuals.zip
    https://dl.dropbox.com/u/8010163/How...e%20Manual.pdf
    https://dl.dropbox.com/u/8010163/Und...c%20washer.pdf
    genospin4yr's Avatar
    genospin4yr Posts: 2, Reputation: 1
    New Member
    		  
    #3

    Aug 27, 2012, 07:50 PM
    Me and a buddy tried to find the spin solenoid. Can not find it. Wonder if have one. I need to add some additional information in case my model newer or something.

    Model number is WJRE555OK2WW

    The water level switch seems to work in relation to water levels however it seems like nothing is telling the machine that the water is all pumped out. The water pump that pumps the water out keeps running. Then it will agitate for a short time the you hear the click for the tub being engage but it will not move much. Then the process will repeat. The whole time it is still trying to pump water out.
    drtom4444's Avatar
    drtom4444 Posts: 3,282, Reputation: 145
    Ultra Member
    		  
    #4

    Aug 27, 2012, 10:15 PM
    Look at the schematic on the machine and see if you see it noted there. The water level switch should tell it that the water is out. Check the schematic well.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Whirlpool washer, agitator works, but during the spin cycle it doesn't spin [ 1 Answers ]

I have a whirlpool washer, I replaced the outer tub and the drive block, but it now doesn't spin. It drains the water, I can hear the motor come on, and feel the vibration . The switch is fine. I looked at the couple, but did not take it apart. The clutch looked fine, sanded the pads and case....

Kenmore Elite Washer does not spin in slow spin cycle until lid is opened and closed [ 0 Answers ]

I have a Kenmore Elite Top Loading Washer, Model 110.24952300. When the washer goes to the spin cycle, it does not spin in the first spin cycle. It does this in the slow spin cycle that precedes the main spin cycle. When it cycles to the regular spin cycle, it does spin properly. I found that...

Kenmore washer 70 series humming at spin cycle - won't spin [ 4 Answers ]

RE: kenmore 70 series model 110.20712990 Type 111 top load washer. Won't spin. Humming noise and a little burning/hot smell when supposed to be spinning. Bypassing the lid switch did not correct the problem. Changed out the motor coupling with no luck... still a humming noise but no smell.

Washer machine will not complete entire cycle. It gets to the spin cycle, and stops. [ 1 Answers ]

I have a GE washer, (about 5 years old). The washer goes through the wash and rinse cycles fine. When it gets to the spin cycle, it stops. I can override and manually place the machine on spin. How can I fix this problem so the cycle runs through completely. Thank You

View more questions Search