Ask Experts Questions for FREE Help !
Ask
    maurice6565's Avatar
    maurice6565 Posts: 4, Reputation: 1
    New Member
    		  
    #1

    Mar 22, 2012, 07:55 AM
    Briggs Stratton 16.5 h.p. Trouble shooting?
    I have a briggs stratton 16.5 model 313707 when I try to start this, it won't spin the flywheel. But if I take out the spark plug it will spin just fine. What is this problem.
    DG's Avatar
    DG Posts: 1,375, Reputation: 109
    Ultra Member
    		  
    #2

    Mar 22, 2012, 08:28 AM
    Sounds like you need to have your valve clearance checked.
    Luck
    ballengerb1's Avatar
    ballengerb1 Posts: 27,378, Reputation: 2280
    Home Repair & Remodeling Expert
    		  
    #3

    Mar 22, 2012, 09:47 AM
    Checking the valves is most likely the best place to start. How long as this engine been sitting without running? Have you checked the oil, was it unexpectedly over filled?
    maurice6565's Avatar
    maurice6565 Posts: 4, Reputation: 1
    New Member
    		  
    #4

    Mar 22, 2012, 10:15 AM
    Just for the winter storage
    maurice6565's Avatar
    maurice6565 Posts: 4, Reputation: 1
    New Member
    		  
    #5

    Mar 22, 2012, 10:17 AM
    What is the valve clearance for this model
    maurice6565's Avatar
    maurice6565 Posts: 4, Reputation: 1
    New Member
    		  
    #6

    Mar 22, 2012, 10:20 AM
    Valve clearance
    What is the valve clearance for this 313707 model type 0126-e1.
    ballengerb1's Avatar
    ballengerb1 Posts: 27,378, Reputation: 2280
    Home Repair & Remodeling Expert
    		  
    #7

    Mar 22, 2012, 10:47 AM
    Check the oil first. Was there gas in the tank over winter?
    ballengerb1's Avatar
    ballengerb1 Posts: 27,378, Reputation: 2280
    Home Repair & Remodeling Expert
    		  
    #8

    Mar 22, 2012, 10:53 AM
    Are you sure about your model number? Small Engine Manuals | Lawn Mower Manuals | Briggs & Stratton This is the engine number and not the tractor model, right?
    DG's Avatar
    DG Posts: 1,375, Reputation: 109
    Ultra Member
    		  
    #9

    Mar 24, 2012, 06:21 PM
    Rotate engine 1/4 inch past top dead center and set valves at .004 both.
    Luck
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Trouble shooting briggs & stratton 19.5 hp engine? [ 0 Answers ]

Have a craftsman 19.5 H I/C Platinum engine. Sat outside for 3 years. Tried to bench start it with a new 12volt battery (engine is not in the tractor). Engine turns over one slow revolution at a time. Cleaned all: contacts, carb, plugs, air filter, fuel filter. Won't start. What can the...

Engine trouble briggs and stratton [ 2 Answers ]

My name is derek and I have a ride on mower the engine is a briggs and stratton and there is a knocking noise coming from the sump. Can anyone tell me what this is likely to be and what needs to be done to repair it. Many thanks in avance of any advoice. All the best for now.

Briggs and stratton lawn mower trouble [ 1 Answers ]

My mower runs but after cutting grass for a minute the mower chokes down and runs like it's trying to cut off and catch up some smoke comes out by and around and through the muffler then cuts off. When I goes and pull the rope to try and start it back some gas sprays out of the exhust muffler on...

18.5hp briggs and stratton trouble [ 1 Answers ]

I have a troy built tractor, I recently purchased it non running "used" after removing and replacing the inline fuel filter I was able to get it to fire . Although it was running rough I believe that it was firing on one side only as It would not accelerate and would die out after about 30 seconds....

View more questions Search