Ask Experts Questions for FREE Help !
Ask
    naesfun's Avatar
    naesfun Posts: 2, Reputation: 1
    New Member
    		  
    #1

    Feb 27, 2007, 09:17 AM
    Heating - Thermostat Control
    I have a maple chase Thermostat control in my home. It was flashing low battery, I changed the battery,I had also noticed the temp had dropped to 63,(at all times I keep it set at 68 in the fall in winter months). Since I have changed the battery I cannot get the temp back up above 60. It will only blow cool air. Can anyone please help me. I have checked the breaker and its fine and there is no pilot light on this system. Please any suggestions
    juggallojed's Avatar
    juggallojed Posts: 165, Reputation: 10
    Junior Member
    		  
    #2

    Feb 27, 2007, 11:02 AM
    Quote Originally Posted by naesfun
    I have a maple chase Thermostat control in my home. It was flashing low battery, I changed the battery,I had also noticed the temp had dropped to 63,(at all times I keep it set at 68 in the fall in winter months). Since I have changed the battery I cannot get the temp back up above 60. It will only blow cool air. Can anyone please help me. I have checked the breaker and its fine and there is no pilot light on this system. Please any suggestions
    Read the faq section

    Then repost the question with details, i.e. : type of furnace

    Fault code if any etc.
    naesfun's Avatar
    naesfun Posts: 2, Reputation: 1
    New Member
    		  
    #3

    Feb 27, 2007, 11:31 AM
    Quote Originally Posted by juggallojed
    read the faq section

    then repost the question with details, ie : type of furnace

    fault code if any ect.
    It is a comfortmaker by RPJ II. I don't have any fault codes.
    labman's Avatar
    labman Posts: 10,580, Reputation: 551
    Uber Member
    		  
    #4

    Feb 27, 2007, 11:57 AM
    Go to
    https://www.askmehelpdesk.com/heatin...ons-58313.html There is an easy procedure for checking if it is the furnace or thermostat. If it is the furnace, go to the sequence of operations. Once you have some idea what the trouble is, you can post back if you need help with specific details.

    If it won't heat and no fault codes, it may be the thermostat.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Heating/ thermostat problems [ 2 Answers ]

I don't know much about HVAC because I haven't had many problems till now. My thermostat (honeywell T8001C) display goes blank and the heat will not turn on. I've tried flipping the breakers in the garage. That won't work. Any ideas?

Underfloor heating thermostat [ 1 Answers ]

I am trying to wire up my underfloor heating but I'm not sure weather the wire with the power is the load or feed, if any one could let me no that would be great. Thanks. Darren

Thermostat heating cycles [ 4 Answers ]

What can happen if I use a heat cycle of 5 versus 3. I bought two honeywell thermostats. RTH6300b. There is some confusion as to what heat setting to use. I have a new oil furnace, a system 2000 furnace with forced hot water. The thermostat says to use a setting of 5 if I have a gas or oil...

Temperature control/thermostat [ 4 Answers ]

Our new home of approximately 2000 sq. ft. has two heating sources, a heat pump for the upstairs and a gas furnace for the first floor. We do not have a basement. The stairway is open to a second floor loft with two bedrooms and a bath enclosed. I have set back thermostats on both heaters. I am...

'C' connection for remote control thermostat [ 2 Answers ]

I have purchased a RiteTemp 8082C Programmable Thermostat with remote control to replace my old mercury swtich type thermostat. While preparing to install the new one, I noticed in the instructions that all of the connections map correctly to my existing setup except one. The instructions say...

View more questions Search