Ask Experts Questions for FREE Help !
Ask
    jpcolleran's Avatar
    jpcolleran Posts: 3, Reputation: 1
    New Member
     
    #1

    Dec 18, 2011, 03:10 PM
    White-Rodgers to Hunter wiring help needed.
    I am replacing a very old W-R thermo (type 125-202) with a Hunter (model 44260). There are 3 wires connected to the W-R, one at position 4, one at % and one at 6. I'm not sure where the wires go on the new hunter. My heating system is hot water base board that has 4 zones, with a thermo for each zone.
    wmproop's Avatar
    wmproop Posts: 3,749, Reputation: 91
    Ultra Member
     
    #2

    Dec 18, 2011, 06:53 PM
    Do the three wires have a color? Are they all the same
    jpcolleran's Avatar
    jpcolleran Posts: 3, Reputation: 1
    New Member
     
    #3

    Dec 18, 2011, 07:01 PM
    Green wire to the terminal marked 4, red wire to terminal 5 and white wire to terminal 6.
    wmproop's Avatar
    wmproop Posts: 3,749, Reputation: 91
    Ultra Member
     
    #4

    Dec 19, 2011, 05:32 AM
    OK, hoping they are wired correctly as to rule of thumb,, the red wire goes to RH or r post
    The green wire to g post
    And the white wire to W post

    With all this said I feel I must warn you Hunter makes about the junkiest thermostat on the market,, if it works at all ,about 1 year is all you will get out of it, if its not to late take it back ,spend a few extra bucks and get yourself a good Honeywell, it will last for years
    jpcolleran's Avatar
    jpcolleran Posts: 3, Reputation: 1
    New Member
     
    #5

    Dec 20, 2011, 04:26 AM
    Thank you very much. Everything is working fine.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Changing Thermostat from White-Rodgers to Hunter, need wiring assistance. Please help [ 1 Answers ]

Hello :) I am trying to replace my White-Rodgers Thermostat (Type: 1F89-73) with a Hunter Touchscreen Programmable Thermostat (Model: 44860). I have a TRANE all electric heat pump system. The wiring is the issue for me, meaning the number of wires and where to place them into the new Hunter...

Changing Thermostat from White-Rodgers to Hunter, need wiring assistance. Please help [ 0 Answers ]

Hello :) I am trying to replace my White-Rodgers Thermostat (Type: 1F89-73) with a Hunter Touchscreen Programmable Thermostat (Model: 44860). I have a TRANE all electric heat pump system. The wiring is the issue for me, meaning the number of wires and where to place them into the new Hunter...

Wiring for thermostat: Going from White Rodgers to Hunter [ 5 Answers ]

Help, someone please! I have a Carrier heat pump with a White Rodgers programmable thermostat that keeps tripping off the settings we use to program... next thing you know the a/c is off and the house begins to warm up to 85 degrees the White Rodgers thermostat defaults to because technically a/c...

White-Rodgers to new Hunter Thermostat (Wiring Help Please) [ 4 Answers ]

Hello, I have a new home, built in 2003, with Central Heat and Air. It's all run off electricity and is using a Lennox Model CB29M-41-1P heat pump. The WHITE ROGERS DIGITAL HEAT PUMP THERMOSTAT 1F89-211 used the following wires: White Red Brown Orange Yellow


View more questions Search