Ask Experts Questions for FREE Help !
Ask
    ginmc1959's Avatar
    ginmc1959 Posts: 3, Reputation: 1
    New Member
    		  
    #1

    Nov 6, 2011, 06:01 PM
    Pressure switch well pump not working?
    Well pump pressure switch won't shut off at 50psi. Replaced switch and still having the same problem with pressure building at least above 70psi and pump needing to be turned off manually. Any ideas?
    jlisenbe's Avatar
    jlisenbe Posts: 5,020, Reputation: 157
    Uber Member
    		  
    #2

    Nov 6, 2011, 07:06 PM
    1. Did you replace the little tube that the switch is attached to? Or at least make sure it's clear and open.

    2. Are the points on the switch opening? If not, and the tube to the switch is clear, then turn the large center nut on the switch two full turns counter clockwise (do this with power off) and see if that helps you. If it does, then continue to adjust the switch by turning counter clockwise to lower pressure cut off and clockwise to raise it.
    ginmc1959's Avatar
    ginmc1959 Posts: 3, Reputation: 1
    New Member
    		  
    #3

    Nov 7, 2011, 02:52 PM
    Thanks so much will give it a go!
    jlisenbe's Avatar
    jlisenbe Posts: 5,020, Reputation: 157
    Uber Member
    		  
    #4

    Nov 7, 2011, 05:32 PM
    Let us know how it goes.
    ginmc1959's Avatar
    ginmc1959 Posts: 3, Reputation: 1
    New Member
    		  
    #5

    Nov 27, 2011, 05:39 PM
    Took awhile to get back to our place in wv where we were having a prob... Thanks so much!. it worked! We did have to turn the middle screw a few more times but now is just fine! Thanks again! Much appreciated!
    jlisenbe's Avatar
    jlisenbe Posts: 5,020, Reputation: 157
    Uber Member
    		  
    #6

    Nov 28, 2011, 12:05 PM
    Great. Isn't it nice to have reliable water again?
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Pump pressure switch [ 6 Answers ]

How do I adjust the pressure switch on a small water well pump, there are two adjustment screws one is larger than the other. Many thanks, M. Ruen

Well pump switch working fine new switch not working? [ 2 Answers ]

I'm having a serious problem. I had a 20-40 that was working fine, but I wanted more pressure so I got a new 40-60. When I got everything hooked up, I was only generating about 40 psi and it would go no higher. Just to be clear, I did raise the pressure tank to 38 psi before starting the pump. I...

Pump pressure switch does not turn on with low pressure [ 0 Answers ]

I lost water in my home overnight. The pressure gage reads about 8 PSI. If I use the lever on the pressure switch to close the contacts, nothing happens. Actually, the pump controller box, makes a buzzing sound for a couple of seconds, but that's it. Does anyone have any thoughts? I don't...

Pressure switch well pump not working [ 1 Answers ]

Installed new pressure switch. Single spring. 10 lbs is all I'm getting. Points are closed, pump not kicking in.

Well pump pressure switch [ 1 Answers ]

Manostat pressure switch ,has 4 screws on front for wires( 2 black wires and 2 white wires)and then two ground wires .These are all the wires coming in for switch . My friend took them off and does not remember how they were hooked up. Please help if you can.Thanks.

View more questions Search