Ask Experts Questions for FREE Help !
Ask
    smiitty's Avatar
    smiitty Posts: 1, Reputation: 1
    New Member
     
    #1

    Feb 18, 2007, 09:10 PM
    Lead & olkum joints
    What is the rope called . Used in pouring a horizontal lead joint. I always used to call it a running rope but is that really what it's called...
    iamgrowler's Avatar
    iamgrowler Posts: 1,421, Reputation: 110
    Ultra Member
     
    #2

    Feb 19, 2007, 06:38 AM
    Quote Originally Posted by smiitty
    what is the rope called . used in pouring a horizontal lead joint. i always used to call it a running rope but is that really what it's called..........
    Oakum.
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
     
    #3

    Feb 19, 2007, 07:31 AM
    Quote Originally Posted by smiitty
    what is the rope called . used in pouring a horizontal lead joint. i always used to call it a running rope but is that really what it's called..........
    I cut my teeth on lead and oakum poured joints. Yes, it's called a "running rope" or a "joint runner". This is a asbestos rope with a attached clamp. We soaked the new rope in used motor oil to limber them up. May I ask why you're asking? Regards, Tom
    doug238's Avatar
    doug238 Posts: 1,560, Reputation: 62
    Ultra Member
     
    #4

    Feb 19, 2007, 06:54 PM
    Joint runner.
    It has been so long since I have done horizontal cast iron I had forgotten. [looked it up on google]
    Cast iron pipes for plumbing
    Assembling horizontal joints
    The same initial procedure applies in making horizontal joints as for vertical ones. Secure the two pieces of pipe firmly in place after making sure they are clean and dry. Any moisture might dampen the oakum, causing lead to fly out or prevent it from filling the joint properly.

    When ready to pour the lead, first attach a tool called a joint-runner. It is made of asbestos and is attached close to the end of the bell. You pour the molten lead in at the top and it finds its way down and around inside the cavity. After the lead has cooled, remove the joint-runner and caulk the lead in firmly, as with vertical joints

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Ball joints [ 3 Answers ]

What would an estimated cost of replacing lower ball joints on my 1998 Ford F150? I called a fairly reliable repair shop this morning and they gave me an estimate of approximately $365. This would include labor and the alignment. I looked at NAPA online and found the lower ball joints at a...

Removing cast iron / lead joints [ 4 Answers ]

Hi; I have a vertical 2 inch cast iron vent pipe that I need to remove to install a medicine cabinet. I have cut it in one spot with a sawzall, but there is also a joint in it where I would like to separate it. The joint appears to be poured with lead. If I heat it with a propane torch to get it...

Leaking drain joints [ 13 Answers ]

I have installed a new kitchen sink, but the slip joints (brass) of the drain pipe leak, even though they have rubber gaskets and I have tightened them with a wrench. I did not use any sealing compound (pipe thread compound). Should I, or are the slip joints designed to function without such a...

Forgot To Prime Joints [ 1 Answers ]

I remembered to prime my pvc pipe, yet forgot to prime just one of the elbows. Am I in danger of a leaky pipe now? Thank you in advance

How to work with lead joints? [ 3 Answers ]

Hello, I am in the middle of adding a bathroom in part of my garage. What is the best way to separate lead joints in cast iron pipe? My home was built in 1957 so I don't know if they were using the hemp type stuff to seal the joints then. The pipe sort of looks galvanized to me (It cut pretty...


View more questions Search