Ask Experts Questions for FREE Help !
Ask
    awedge's Avatar
    awedge Posts: 5, Reputation: 1
    New Member
    		  
    #1

    Jul 5, 2011, 11:49 AM
    Briggs 16hp V-twin no spark
    I have a briggs Vanguard 16hp V-Twin with no spark. Had trouble with it a couple months back (no fuel and no Spark on one side). This engine is mounted in a van and used for turning carpet cleaning equipment Gets a lot of hours year round. I figured I'd do some work on it while I had it out, here is what all got done: Replaced head gaskets, rebuilt and cleaned carb, new solenoid, new plugs, new fuel filter, adjusted valves (set to .004) and replaced the magneto on side with no spark.

    Been working and running fine for a couple months until today. Started right up and ran for about 10 minutes and shut down. Would crank but will not fire. Plugs looked pretty dirty for only a couple months old so replaced them again and checked for spark. Spark was there with new plugs but seemed intermittent/week. Put them back in and tried to start it, no fire. After checking spark again, I now have none. Like I said, one magneto is new and it is not likely both would go at the same time. Anything else I should check? The only kill switch is connected to a float in the dirty water tank, tank gets full, shuts down the engine as not to over flow the tank, seems to be functioning fine.
    DG's Avatar
    DG Posts: 1,375, Reputation: 109
    Ultra Member
    		  
    #2

    Jul 5, 2011, 08:43 PM

    Unhook the ground wire where it hooks to the engine and check for fire, depending on the model # of the engine it could have an inline diode going to the coils. If you could give the model and type I could check and see.
    awedge's Avatar
    awedge Posts: 5, Reputation: 1
    New Member
    		  
    #3

    Jul 5, 2011, 10:23 PM
    Not sure why I didn't give the #'s to start with. Model= 305447 Type= 0079-E1 By ground wire, you mean the main coming from the battery? That's the only ground I see going to the engine.
    DG's Avatar
    DG Posts: 1,375, Reputation: 109
    Ultra Member
    		  
    #4

    Jul 6, 2011, 05:02 AM

    Imean the little kill wire going to the coils on the engine ,should hook on the side to what looks like a little square plastic nut.
    awedge's Avatar
    awedge Posts: 5, Reputation: 1
    New Member
    		  
    #5

    Jul 6, 2011, 05:40 AM
    Yes sir, unhooking that ground did in fact give me spark back. It will even start and run but sounds like it has no power at all.
    awedge's Avatar
    awedge Posts: 5, Reputation: 1
    New Member
    		  
    #6

    Jul 6, 2011, 08:30 AM
    Ok, take that back, it was only running rough because I did not put the spark plug wire back on one side. HAHA, with both plugs firing it runs just fine. The ground wire (x2) I removed as you asked, looks like one traces back to the ignition switch (key) and the other goes to an oil/water pressure bypass switch. On this unit the switch is used to start the engine. Hold the switch over while starting to bypass oil and water pressure until it builds up.

    As it sits right now, it seems as if I could go clean some carpets and make a few bucks, but obviously there is still something wrong.
    awedge's Avatar
    awedge Posts: 5, Reputation: 1
    New Member
    		  
    #7

    Jul 6, 2011, 08:34 AM
    Comment on awedge's post
    This may be a stupid question but... What are the coils anyway. I pretty much have taken this thing apart three times and put it back together again and still do not know what or where the coils are.
    DG's Avatar
    DG Posts: 1,375, Reputation: 109
    Ultra Member
    		  
    #8

    Jul 6, 2011, 06:13 PM

    Its showing that it could have diodes inline going to the coils.need to remove engine blower housing and check it out.
    Part # 578A or 578E . Luck
    Attached Images
     
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

1994 Briggs/Stratton 16HP Twin II (Runs but won't stay running) [ 10 Answers ]

This motor is on a 1994 Murray riding mower. The initial problem started last year when I lost spark in 1 cylinder. I replaced the coil, regained spark in both cylinders. But now this season, it will only run if gas is poured into carburetor, it seems to have vacuum but carb won't pull gas through....

Briggs and stratton vanguard 16 hp twin engine with no spark [ 10 Answers ]

I have a new Briggs and Stratton Vanguard 16hp twin installed in an ATV. Unfortunately on a shakedown run the exhaust pipe loosened and fell on the wireing harness from the ignition key and the engine immediately stopped as the pipe melted through the wire insulation, I assume shorting something...

Briggs and Stratton opposed twin NO SPARK [ 2 Answers ]

I have an old dresser lawn tractor. It was running when I parked it last fall. Now it cranks but won't start. I can't detect any spark. I removed the kill wire from the magneto & jumped the solenoid; spins, but still no spark. There are interlocks on the mower engage lever, but the clutch & seat...

Briggs & Stratton Vanguard 16HP OHV No Spark? [ 3 Answers ]

Hi All, Seen several threads along this line but nothing that seems to help me. I have a Briggs & Stratton Model 303777 Vanguard (on a 1994 Snapper SR170 Rider). The engine turns over well, but will not start. I am not getting any "thump" when it turns. I am not hearing any clicking from the...

View more questions Search