Ask Experts Questions for FREE Help !
Ask
    ummee's Avatar
    ummee Posts: 2, Reputation: 1
    New Member
    		  
    #1

    May 27, 2011, 11:59 AM
    Fix gear roller
    Hello,
    I want your assistance in the following question:

    I have a machine which produce PP strapping band in which three roller stand are installed i.e 1st, 2nd, and 3rd, which are connected with the Dc gear motor,and its speed can be controlled through inverter, and it is used to change the speed of roller stand,
    The problem is that 1st roller stand gear motor has been misplaced, and I don't know description of that gear motor, I have got the following information available:

    Roller speed : min 0, max 24m/min

    I want to know is it possible for you to calculate gear motor ratio using roller speed i.e max 24 m/min, or is there any other way around

    For your assistance I have got the full description of 2nd and 3rd roller stand:

    Roller speed : min 0, max 160m/min
    Rpm of motor : 1735
    Cycles : 60hz
    Gear ratio : 1/10

    PLease help me out, I shall be thankful to you for this act of kindness
    ummee's Avatar
    ummee Posts: 2, Reputation: 1
    New Member
    		  
    #2

    May 27, 2011, 12:02 PM
    Hello, I want your assistance in the following question: I have a machine which prod
    Hello,
    I want your assistance in the following question:

    I have a machine which produce PP strapping band in which three roller stand are installed i.e 1st, 2nd, and 3rd, which are connected with the Dc gear motor,and its speed can be controlled through inverter, and it is used to change the speed of roller stand,
    The problem is that 1st roller stand gear motor has been misplaced, and I don't know description of that gear motor, I have got the following information available:

    Roller speed : min 0, max 24m/min

    I want to know is it possible for you to calculate gear motor ratio using roller speed i.e max 24 m/min, or is there any other way around

    For your assistance I have got the full description of 2nd and 3rd roller stand:

    Roller speed : min 0, max 160m/min
    Rpm of motor : 1735
    Cycles : 60hz
    Gear ratio : 1/10

    PLease help me out, I shall be thankful to you for this act of kindness
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Out feed table saw PVC roller stand roller encaps [ 0 Answers ]

Some time ago I saw a set of fold up table rollers for use with table saw. These rollers were from 2in PVC pipe with molded end caps inserted into each end with a center pin into which each roller was inserted into oak rails. Thanks much, Wilson

Car gear not switching to 2nd gear [ 0 Answers ]

My toyota 98 camry can't switch form 1st to 2nd gear, Goes reverse.. Dashboard is off at the same time, no speed no rpm, no temp. please help

Repalace ring gear gear on brigg and sratton 14.5 engine [ 1 Answers ]

How do you removed the ring gear from the fly wheel and put on new one on the teeth is worn out and the starter will not turn the motor

Roller coasters [ 1 Answers ]

I have never been on a big roller coaster and I am going to go on one June ninth one of my questions is is it better to close your eyes or leave them open on the roller coaster Another one is should I sit in the front or in the back

How do I know which Roller to fix? [ 3 Answers ]

I have a squeaky dryer, someone told me to change the roller. How do I know where the roller is or what kind of roller I need?

View more questions Search