Ask Experts Questions for FREE Help !
Ask
    Robertl110's Avatar
    Robertl110 Posts: 2, Reputation: 1
    New Member
    		  
    #1

    May 21, 2011, 12:17 PM
    Deere L110 transaxle fan
    Several of the blades on the transaxle fan have sheared off. Can someone advise how easy it is to replace the fan? Is it done from the top or does the axle have to come off (probably beyond what I would undertake)? Does the fan cool the transmission or the belt? It seems very small to have any measurable cooling effect..?

    For the short term is it ill advised to use the L110 until the fan is fixed?

    Thanks for the help.
    DG's Avatar
    DG Posts: 1,375, Reputation: 109
    Ultra Member
    		  
    #2

    May 21, 2011, 04:10 PM

    Should be able to reach in on the side and replace fan,
    I always remove the tire and wheel for easy access.
    And to answer ? Its to cool tranny.
    Luck
    Robertl110's Avatar
    Robertl110 Posts: 2, Reputation: 1
    New Member
    		  
    #3

    May 21, 2011, 05:26 PM
    Comment on DG's post
    DG Thanks. I removed the "shroud" above the belt/pulley/fan assembly and can not figure out how to remove the pulley so I can get to the fan. The fan wings were apparently digging into the belt which is going to need replacement too.
    DG's Avatar
    DG Posts: 1,375, Reputation: 109
    Ultra Member
    		  
    #4

    May 21, 2011, 05:39 PM
    This is what it should look like # 2 is a snap ring remove this and it should come off.
    Luck
    Attached Images
     
    icefish's Avatar
    icefish Posts: 1, Reputation: 1
    New Member
    		  
    #5

    Sep 11, 2011, 08:27 AM
    I just did this as well. You should also replace the "wobbly" washer that is item 4 in the diagram above. A John Deere technician told me that it worth replacing when replacing a fan. (I think the washer was around a dollar).

    *** The snap ring is a nightmare to remove unless you have the correct size, 90 degree, snap ring pliers. It is really tight in there. I did not remove the tire as others have mentioned, just the fan guard above the pulley.

Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

John Deere L120 Transaxle [ 12 Answers ]

Is there a way to add hydraulic fluid to a John Deere L120 riding mower? Background: it's about 5 years old. This year it is having difficulty going up hills. I thought it might be the belt, so with the unit upright, I replaced the belt. Now, it won't go at all. I believe (is this possible?)...

John deere transaxle [ 4 Answers ]

I'm having problem with me L120 John Deere once it gets hot it won't climb hills I know for a fact its not the belt I replaced it and it is routed correctly I was told it was a valve problem and that the transaxle is sealed but this is not the case I was able to separate the transaxle by removing...

John Deere L110 [ 1 Answers ]

How do I reconnect the deck to the tractor? My wife took it off and I'm trying to put it back.

Deere L110 [ 1 Answers ]

How do you remove the carburetor bowl ? What is the purpose of the electrical connection attached to the carburetor ? I have water in the fuel system and want to clean the carburetor bowl. Can't see how it is attached.

John Deere L110 [ 3 Answers ]

I have a 2003 John Deere L110. At the beginning of this mowing season, when I cranked it, the engine tried to crank with it in the run position and stopped cranking in the crank position! Then it just stopped cranking altogether. I replaced the ignition switch and that did not help. I replaced...

View more questions Search