Ask Experts Questions for FREE Help !
Ask
    Kyle_in_rure's Avatar
    Kyle_in_rure Posts: 341, Reputation: 10
    Full Member
    		  
    #1

    Apr 17, 2011, 01:07 PM
    Should I replace the breaker?
    I have two barns on the same electrical circuit. With both barns together there are five receptacles and about 5 or 6 lights. The first barn is wired with primarily 10 AWG wire, and the second (fed from the first) is wired with 12 AWG.I would like to install some sort of "switch" that would allow me to cut all power to the second barn from the first. Can I just install a 20 AMP light switch or is this a bad idea? Should I change the breaker from 30 amp to 20 or can I do that? What should I do?
    tkrussell's Avatar
    tkrussell Posts: 9,659, Reputation: 725
    Uber Member
    		  
    #2

    Apr 18, 2011, 04:36 AM

    Any separate building fed by another always needs some sort of disconnect.

    A simple 20 amp switch will work fine as a disconnecting means for one circuit.
    Kyle_in_rure's Avatar
    Kyle_in_rure Posts: 341, Reputation: 10
    Full Member
    		  
    #3

    Apr 18, 2011, 02:43 PM
    Comment on tkrussell's post
    Yes but since the circuit is on a 30 AMP breaker could I (in theory--although I doubt it would happen) overload the switch?
    tkrussell's Avatar
    tkrussell Posts: 9,659, Reputation: 725
    Uber Member
    		  
    #4

    Apr 19, 2011, 02:26 AM
    I completely missed where you mention a 30 amp breaker, due to the #12 wire in the circuit, yes, it needs to be changed to a 20 amp.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

How do I replace a 30 amp breaker with a 20 amp breaker? Must I replace the wiring? [ 15 Answers ]

I have purchased a GE built-in oven to replace the 60 year old oven that was installed when the house was built. The original oven uses a 30 amp breaker. The salesperson told me I must change the breaker to a 20 amp to accommodate the new oven, but he's unsure whether the wiring must be changed as...

I just replace my breaker box but it didn't have a main breaker is that safe ? [ 5 Answers ]

On the box it says it is a 100 amp breaker box and I have 1 50 amp breaker .2 30 amps breaker and 3 20 amps breakers if I add all the breaker it is 170 amps and my breaker box is for 100 amps is that how it works? Do I need a bigger breaker box? Is it unsafe...

Do I need to replace the circuit breaker? [ 6 Answers ]

I live in a 12 year old house and yesterday I took down our front porch lights (2 on each side of the front door) to paint them. I turned off the breaker during this process, painted the lights, put them back up and went to turn on the breaker. I switched it over and noticed that it would go to the...

Can I replace a 20amp breaker with a 25amp breaker safely? [ 1 Answers ]

Can I safely replace a 20amp breaker with a 25amp breaker... application is a pool pump. The motor is drawing too much on the 20A line...

Replace the Breaker? [ 3 Answers ]

So how do I replace this 10Ka 120/240V breaker since my dryer will not heat and I have replaced all its parts. I think I have to replace the breaker (2 pole - single breaker), because when I tested it with my meter, sometimes I would get 120 readings and other times 230 - 240 readings.

View more questions Search