Ask Experts Questions for FREE Help !
Ask
    jbob23's Avatar
    jbob23 Posts: 2, Reputation: 1
    New Member
    		  
    #1

    Feb 6, 2011, 12:30 PM
    Need to match my old intertherm wiring to new lux stat.
    The colors are red, orange, yellow, blue, black, white and green. The options on the back of my LUX TX9000b are RC RH B W G O Y. IT seems most of these match up but with just one B on the back is it Black or Blue what goes to RC RH. I read red would go there but that leaves me with the extra B word wire.
    ballengerb1's Avatar
    ballengerb1 Posts: 27,378, Reputation: 2280
    Home Repair & Remodeling Expert
    		  
    #2

    Feb 6, 2011, 12:43 PM

    RC to RH is usually jumpered. Try this for more help https://www.askmehelpdesk.com/electr...92#post2698846



    Second post talks about wiring colors
    jbob23's Avatar
    jbob23 Posts: 2, Reputation: 1
    New Member
    		  
    #3

    Feb 6, 2011, 01:42 PM
    Red would be to the RH side and they are jumpered. I have blue as the extra wire. Anybody? Does this sound right?
    ballengerb1's Avatar
    ballengerb1 Posts: 27,378, Reputation: 2280
    Home Repair & Remodeling Expert
    		  
    #4

    Feb 6, 2011, 02:00 PM

    Blue from the furnace or coming from the stat? I think I gave you the wrong link before, try this on. https://www.askmehelpdesk.com/heatin...eat-58313.html post2 tells about wiring
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Intertherm furnace/ac won't shut off in heat or cool mode even with t-stat disconnectd [ 1 Answers ]

I disconnected the t-stat wires and it still runs all the time whether in heat or cool mode. It blows heat and cool properly, just won't shut off... have to kill the breaker. Any ideas would be great. Thanks a million, Murfdogger

Lux T-Stat with Amana gas heat/electric cool [ 2 Answers ]

Hi everyone, I hooked up a Lux stat from Ace. Three position switch - heat/off/cool. Two position fan switch - auto/on. Caped the blue in the unit going to the -24V side of the condenser contactor in the unit. Jumped the RH RC terminals for a single transformer. The heat works great...

Honeywell wiring need to connect to a lux tx9000ts wiring [ 5 Answers ]

I am replacing a honeywell non-programmable with a Lux TX9000TS. The old wiring inputs show e, aux, y, g, o, l, r, b, c (with is optional with batteries) and the new lux is w,y,g,b,o,rc,rh,c. Which wires go were?

Need to match wires to t-stat terminals [ 6 Answers ]

When my house was built 3 years ago, a Bryant multistage heat pump was installed. Initially a Honeywell T8411R Electronic Heat pump thermostat was installed as well as a built in humidifier. There are wires going to the thermostat with the brown and black wires being hooked to the humidifier. ...

Old Intertherm t-stat out,what to put in? [ 4 Answers ]

I have a mobile home with an Intertherm furnace, used for both heating ond cooling. I have one T-stat that controls which function is to be used,(heating/cooling). This one controls the cooling temp,and fan. I have a second T-stat that controls the heat temp. It is an old two wire mechanical and I...

View more questions Search