Ask Experts Questions for FREE Help !
Ask
    bduke1946's Avatar
    bduke1946 Posts: 10, Reputation: 1
    New Member
    		  
    #1

    Oct 17, 2010, 02:46 PM
    Still can not find flywheel timing marks kohler k321 s engine
    Spent 3 hrs looking for S or T mark on flywheel & did not find any. Are marks stamped on face or flange or teeth of flywheel? Installed new ignition points & condenser & plug using method posted by DG & it runs fairly well , but I think timing is not correct.Thank YOU DG for your help
    DG's Avatar
    DG Posts: 1,375, Reputation: 109
    Ultra Member
    		  
    #2

    Oct 17, 2010, 03:19 PM

    Its on the flange behind the teeth it is real hard to see , it is stamped in the ring
    Spray wd40 or sometype of spay
    This will make it eaier to spot.
    Luck
    bduke1946's Avatar
    bduke1946 Posts: 10, Reputation: 1
    New Member
    		  
    #3

    Oct 17, 2010, 03:32 PM
    Comment on DG's post
    Thank you for all your help. Will try to locate mark tomorrow after work. This 1st Kohler engine I have worked on & not doing a very good job so far.
    DG's Avatar
    DG Posts: 1,375, Reputation: 109
    Ultra Member
    		  
    #4

    Oct 18, 2010, 08:20 AM

    The "s" should be about 1/4 turn before top dead center ,
    DG's Avatar
    DG Posts: 1,375, Reputation: 109
    Ultra Member
    		  
    #5

    Oct 19, 2010, 07:26 AM

    I know this is a kohler , but what type of unit is it on.
    bduke1946's Avatar
    bduke1946 Posts: 10, Reputation: 1
    New Member
    		  
    #6

    Oct 19, 2010, 04:14 PM
    Comment on DG's post
    Had little time to work on engine today & found T on flywheel but could not locate S mark. Found a very faint mark about 1/4 turn past T that appeared to be SP. Could this be the S mark? Thank you for your help.
    bduke1946's Avatar
    bduke1946 Posts: 10, Reputation: 1
    New Member
    		  
    #7

    Oct 19, 2010, 04:23 PM
    Comment on DG's post
    A 1983 Power King tractor model 2414 .
    thelastscout's Avatar
    thelastscout Posts: 1, Reputation: 1
    New Member
    		  
    #8

    Mar 10, 2011, 04:59 AM
    Comment on DG's post
    Yes it is S or SP for firing point for k91 - k341
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search


Check out some similar questions!

Flywheel timing marks location on kohler k321s engine. [ 2 Answers ]

I have a Kohler K321S engine I am trying to adjust ignition timing after installing new ignition points.I cannot find any marks on flywheel. This a 12 volt battery ignition system.The Kohler manual states there is a s & a t mark on flywheel,but can't find any on this one. Could anyone tell me where...

Install ignition points kohler k321 engine? [ 0 Answers ]

Timing hole location kohler k321s engine? [ 1 Answers ]

Timing hole location kohler k321s engine? [ 1 Answers ]

I changed the timing belt on 92 honda accord put all timing marks where they belong [ 2 Answers ]

I changed the timing belt on my 92 honda accord, put all timing marks where they belong. But the car won't start. It sounds like it wants to start but it does not.

View more questions Search