Ask Experts Questions for FREE Help !
Ask
    rreilly's Avatar
    rreilly Posts: 3, Reputation: 1
    New Member
    		  
    #1

    Aug 21, 2010, 01:13 PM
    Shower faucet identification
    I am replacing my shower's escutcheon, handle, etc.. What I've learned (no surprise to folks here) is that shower parts are like car parts... you have to know what you're dealing with to get the right parts. That's my problem. What do I have? See picture.
    rreilly's Avatar
    rreilly Posts: 3, Reputation: 1
    New Member
    		  
    #2

    Aug 21, 2010, 01:15 PM
    Sorry -- didn't attach picture -- attached here.
    Attached Images
     
    massplumber2008's Avatar
    massplumber2008 Posts: 12,832, Reputation: 1212
    Senior Plumbing Expert
    		  
    #3

    Aug 21, 2010, 02:43 PM

    Hi Rreilly...

    It looks exactly like a DELTA brand valve/faucet.

    Take the picture with you to a local plumbing supply store... should be able to help you.

    Mark
    afaroo's Avatar
    afaroo Posts: 4,006, Reputation: 251
    Ultra Member
    		  
    #4

    Aug 21, 2010, 07:09 PM

    Hello Rreilly,

    Open the link below I think this is your faucet, it will show you all the parts that you need, Thanks.

    John

    http://www.plumbingpartsdepot.com/delta600series.pdf
    rreilly's Avatar
    rreilly Posts: 3, Reputation: 1
    New Member
    		  
    #5

    Aug 21, 2010, 07:39 PM

    Thanks. I tried the Delta 600 but it was too small. Chasing a possible Valley faucet. I *think* my rough in valve is a Watco.
    afaroo's Avatar
    afaroo Posts: 4,006, Reputation: 251
    Ultra Member
    		  
    #6

    Aug 21, 2010, 08:00 PM

    In that case follow Mark's advice, Take the picture or remove the parts that you need with you to a local plumbing supply store, some one will help you, Thanks.

    John
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Need to replace 'O' rings and Gaskets in Delta Faucet [ 1 Answers ]

My Delta faucet which is probably 30 years old constantly drips. I have replaced the shower head so know it is the faucet. It is a single handle push up for on and twist to the right or left for temperature control. How do I replace the o rings and gaskets? Thank you

Tub to tub/shower conversion: Need to re-route water lines for a shower faucet? [ 12 Answers ]

Hello everyone, My wife and I just moved into an old (1930s) Spanish house in Los Angeles. We have 2 bathrooms, with the master bathroom containing a bathtub and a separate shower stall. The shower stall is tight with a low ceiling and the bathroom has no exhaust fan (only 2 windows) and...

Shower faucet [ 3 Answers ]

I have a one-handle chrome Delta shower faucet that is leaking from the shower head. I am trying to take it apart to replace seals/springs. It's at least 20 yrs. Old. The problem, I cannot get the threaded ring that holds the thing together to loosen. I've used penetrating oil a couple times...

Water suppressor needed on lavatory faucet and shower faucet? [ 1 Answers ]

Are water suppressors needed in the bathroom sink faucet and the shower stub out also? And can you just use a length of pipe on a T, or must you use those copper chambers? (cpvc system) thanks

Shower faucet [ 3 Answers ]

Hi, When I turn on the shower the water still runs out of faucet.

View more questions Search