Ask Experts Questions for FREE Help !
Ask
    rdzierniejko's Avatar
    rdzierniejko Posts: 10, Reputation: 1
    New Member
    		  
    #1

    Jun 6, 2010, 09:37 AM
    Honeywell Focus Pro 6000 (A/C shuts off)
    Hello:

    I have a Honeywell Focus Pro 6000. If I shut down the unit for an extended period (multiple hours) and then turn it back on, it works perfectly. Within an hour, however, the A/C has stopped working. The unit is still humming, but only a moderate amount of "air temperature" air is blowing out of the vents. Why would this be the case?

    Thanks!
    Joshdta's Avatar
    Joshdta Posts: 2,549, Reputation: 45
    Ultra Member
    		  
    #2

    Jun 6, 2010, 10:05 AM

    Sounds like you have a fan motor getting hot and shutting down.
    rdzierniejko's Avatar
    rdzierniejko Posts: 10, Reputation: 1
    New Member
    		  
    #3

    Jun 6, 2010, 10:13 AM

    How do I fix something like this? Thx again.
    rdzierniejko's Avatar
    rdzierniejko Posts: 10, Reputation: 1
    New Member
    		  
    #4

    Jun 28, 2010, 09:18 PM

    So I pulled the filter off the AC unit in the ceiling last night after noticing a puddle of water on the floor. There is a 1/4" layer of ice underneath the filter. Why would this be the case? I have turned the AC unit off and am letting it thaw out.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Vulcan CX90 and Honeywell Focus Pro 6000 [ 2 Answers ]

Hi, I'm trying to install a Honeywell Focus Pro 6000 controller to a Vulcan CX90 Ducted Heating Unit. There are 6 wires coming from the CX90 marked A,B,C,D,E & F. The wiring diagram for the CX90 is no help because all 6 wires disappear into a decoder unit. Can anyone offer any help on wiring...

Honeywell pro 6000 heat pump Thermostat [ 9 Answers ]

I was told by an AC/Heat repair man that the Honeywell Pro 6000 is the best way to go since I can't afford the top of the line ones they have. My problem is there are so many different model numbers in the Pro 6000, which one is best, which one should I get? I have a heat pump system.

Honeywell Focus Pro 6000 (Heat and A/C reversed) [ 2 Answers ]

I recently purchased a loft. The unit had an existing "Mammoth -- Water Source Heat Pump" thermostat. I purchased a Honeywell Focus Pro 6000 to replace this. I have hooked up the new thermostat, but the heat and A/C are reversed. In other words, to get the heat working, I need to set the system...

Hard wire focus Pro 6000 thermostat [ 1 Answers ]

I just installed a Honeywell focus pro 6000 programmable thermostat I have a boiler with a indirect hotwater tank and a taco sr502 switching relay.. On thermostat I wire red to r white to w and blue to c. On switching relay I wire white to on left termial and red to right termial which I had the...

Wiring a Honeywell Focus Pro 6000 [ 1 Answers ]

I have a Carrier Heat Pump (about 5 years old) that had a non-programmable White Rodgers thermostat 1F59-11. The configuration of wires for the old thermostat are as follows: C = blue wire G= green wire R = red wire O = orange wire W= white wire Y = yellow wire L = empty B = empty

View more questions Search