Ask Experts Questions for FREE Help !
Ask
    bigkentuckey's Avatar
    bigkentuckey Posts: 3, Reputation: 1
    New Member
     
    #1

    May 24, 2010, 01:20 AM
    1995 vintage Cub Cadet 1641,16HP Briggs and Stratton Vanguard throttle assy problem,
    I can't figure out how the throttle, governor, linkages and springs are to be re-assembled. Anyone know where to get a picture or diagram on how all this goes together.
    crigby's Avatar
    crigby Posts: 4,343, Reputation: 107
    Outdoor Power Equipment Expert
     
    #2

    May 25, 2010, 05:03 PM

    Hi,
    I will give a link. Speed depends on the other end, not yours, as I have a high-speed one and I could not control it.
    http://www.mymowerparts.com/pdf/Brig...20STRATTON.pdf
    Peace,
    Clarke
    bigkentuckey's Avatar
    bigkentuckey Posts: 3, Reputation: 1
    New Member
     
    #3

    Jun 6, 2010, 01:17 PM
    Quote Originally Posted by crigby View Post
    Hi,
    I will give a link. Speed depends on the other end, not yours, as I have a high-speed one and I could not control it.
    http://www.mymowerparts.com/pdf/Brig...20STRATTON.pdf
    Peace,
    Clarke
    Perfect... exactly what I needed... Thanks
    bigkentuckey's Avatar
    bigkentuckey Posts: 3, Reputation: 1
    New Member
     
    #4

    Jun 6, 2010, 01:17 PM

    Perfect... Thanks

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Briggs & Stratton 16hp vanguard [ 11 Answers ]

I have a simplicity mower (1998) with a 16hp vertical shaft vanguard v-twin engine (303777 1111-51). Yesterday, after running the mower with turbo bagger attachment (a little extra load on the engine), for about 20 minutes, I idled back the engine and it began belching large clouds of blue/white...

Excess crankcase pressure in briggs and stratton 16hp vanguard OHV engine [ 2 Answers ]

There is an excess amount of oil being pushed out of the crankcase breather tube into the air filter housing. The compression is fine and there is no smoke out the exhaust. I am thinking a head gasket is the problem. Anyone have any experience with this problem?

16hp Briggs & Stratton Vanguard Carb Question [ 3 Answers ]

I have a 16HP B&S Overhead Valve Engine. I installed it in my golf cart which previously had a Honda 8hp OHV engine. Salisbury belt drive torque converter system. The new B&S engine doesn't seem to idle slow enough to keep the driver clutch from starting to engage. With tension on the belt, I...

Briggs & Stratton 16HP Vanguard Motor [ 4 Answers ]

Hi, I have a B & S 16Hp Vanguard motor that runs hydraulic tools. The motor was smoking and running rough so I replaced the oil, gas, and air filter. I started it up with out the oil filter on and the motor runs perfect. I reinstall the air filter and the motor begins to choke out and run...

Briggs & Stratton Vanguard 16HP OHV No Spark? [ 3 Answers ]

Hi All, Seen several threads along this line but nothing that seems to help me. I have a Briggs & Stratton Model 303777 Vanguard (on a 1994 Snapper SR170 Rider). The engine turns over well, but will not start. I am not getting any "thump" when it turns. I am not hearing any clicking from the...


View more questions Search