Ask Experts Questions for FREE Help !
Ask
    shadowgypsy's Avatar
    shadowgypsy Posts: 5, Reputation: 1
    New Member
    		  
    #1

    Apr 11, 2010, 12:42 PM
    I have an intertherm furnace with outside unit. Someone cut a bunch of pieces out. Ho
    I have an intertherm furnace. Someone cut out all the wiring hook-ups for the thermostat and fan, and the outdoor unit. Does anyone know how (or where) to put the wires to get everything working?
    Joshdta's Avatar
    Joshdta Posts: 2,549, Reputation: 45
    Ultra Member
    		  
    #2

    Apr 11, 2010, 12:58 PM

    Just the low voltage t-stat wire? Are there any parts missing? Is the 110 volt hooked up?
    shadowgypsy's Avatar
    shadowgypsy Posts: 5, Reputation: 1
    New Member
    		  
    #3

    Apr 11, 2010, 01:02 PM

    Everything is there but terminal block. Not sure how to put wires together to make everything work in proper sequence
    Joshdta's Avatar
    Joshdta Posts: 2,549, Reputation: 45
    Ultra Member
    		  
    #4

    Apr 11, 2010, 02:13 PM

    Is it a electric furnace, or gas?
    shadowgypsy's Avatar
    shadowgypsy Posts: 5, Reputation: 1
    New Member
    		  
    #5

    Apr 11, 2010, 03:01 PM
    Electric
    shadowgypsy's Avatar
    shadowgypsy Posts: 5, Reputation: 1
    New Member
    		  
    #6

    Apr 11, 2010, 03:28 PM

    I also found its old switching box. But I still can't find the thermostat hook up. How would I put the thermostat wires. I have (r) (w) (y) (g) coming down from thermostat. (r) (b) from transformer, (r) (w) from outide unit. The switch box has (r) (b) low voltage, and (w) (g) high voltage coming out. I'm lost as to where to hook up what. I have a little experience, but not enough to follow this chop shop job. Thanks for your help
    Joshdta's Avatar
    Joshdta Posts: 2,549, Reputation: 45
    Ultra Member
    		  
    #7

    Apr 11, 2010, 04:56 PM

    Are you trying to get the ac to work or the heat? Or both. If you have not termanal block then you may not have the ac relay either.
    shadowgypsy's Avatar
    shadowgypsy Posts: 5, Reputation: 1
    New Member
    		  
    #8

    Apr 11, 2010, 05:12 PM

    Trying to get both to work. I have a full array of sequencers and switches
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

How to determine if intertherm unit for mobile home has heat unit? [ 2 Answers ]

Does intertherm ac model ASCB-030-BBBB have a heating unit. This unit does cool sufficiently for mobile home installation.

Live in a mobile home with intertherm heat and air unit the unit outside unit has bee [ 1 Answers ]

Live in mobile home with an intertherm unit outside unit is no longer running didn't know if it even needs to be running with the heat

Intertherm furnace e2eb-017hb runs briefly, shuts off, then furnace just clicks [ 3 Answers ]

I have an Intertherm furnace, e2eb-017hb. It comes on briefly, blows warm air, then shuts off, and a clicking sound comes from the coil contacts area. I have tested the t-stat, and also replaced a coil contact, thinking that was the problem. I would appreciate any help on what to do next.

Coleman furnace fixed- flue had bird nest a bunch! [ 6 Answers ]

That's it boys cleaned it runs like a champ.Nobody even said to check that on here I can't believe that such a shame I bet most of you have the same and don't even no it.:eek:

My intertherm furnace pilot lights but furnace won't kick on [ 5 Answers ]

I need some diagnostic help. We have a full propane tank. A new burner plate (last year) and the blower works. We light the pilot but the knob should pop up after one minute thus lighting the furnace. It won't pop up. What part should we replace? The furnace is a 17 year old Intertherm MGH...

View more questions Search