Ask Experts Questions for FREE Help !
Ask
    tracechurch1's Avatar
    tracechurch1 Posts: 3, Reputation: 1
    New Member
    		  
    #1

    Mar 22, 2010, 03:00 PM
    I have a 4010 jon deer and I drove it up to the garage and now it won't move
    How would I fix my john deere 4010 it was moving before I rebuit the loader cylinders and now it won't do anything is there any thing I can do to get it moving again
    DG's Avatar
    DG Posts: 1,375, Reputation: 109
    Ultra Member
    		  
    #2

    Mar 23, 2010, 05:13 AM


    I'm guessing you checked the hydro fluid ?
    freedhardwoods's Avatar
    freedhardwoods Posts: 42, Reputation: 3
    Junior Member
    		  
    #3

    Mar 23, 2010, 07:56 AM

    4010s were built in the early 60s. There is nothing to program on them.

    Can you give any more details? What exactly is it doing. What does it sound like.
    tracechurch1's Avatar
    tracechurch1 Posts: 3, Reputation: 1
    New Member
    		  
    #4

    Mar 23, 2010, 09:04 AM
    Quote Originally Posted by freedhardwoods View Post
    4010s were built in the early 60s. There is nothing to program on them.

    Can you give any more details? What exactly is it doing. What does it sound like.
    It had clutch when I parked it and now it don't what will happen if I adjust the fingers on the clutch because that is what I did now I have full clutch pedal but I haven't tried to move it yet I wanted someone's opinion on that before I tried it
    crigby's Avatar
    crigby Posts: 4,343, Reputation: 107
    Outdoor Power Equipment Expert
    		  
    #5

    Mar 23, 2010, 10:26 AM

    Hi,
    You say you built the loader cylinders? I would say you have air in the hydraulics. With the engine running, move all loader controls to achieve full operation. Check fluid levels and add as needed. Make sure you did not lock park brake and operate drive system normally to see if it will bleed clear. If it does start moving, Deere recommends sharp turns in both directions to finish the job.
    Peace,
    Clarke
    freedhardwoods's Avatar
    freedhardwoods Posts: 42, Reputation: 3
    Junior Member
    		  
    #6

    Mar 23, 2010, 06:10 PM

    Everyone else is giving replies about a hydrostatic drive. A 4010 has an 8 speed, gear driven transmission.

    If the clutch feels right it should be OK, but not knowing why it backed off makes me hesitant to tell you to try it. Do you have any idea why it backed off?
    crigby's Avatar
    crigby Posts: 4,343, Reputation: 107
    Outdoor Power Equipment Expert
    		  
    #7

    Mar 24, 2010, 06:21 AM

    Hi,
    There are in fact two 4010s. One is called a wheeled tractor as one person pointed out. The other is a CUT for Compact Utility Tractor and is far newer. Perhaps you should advise of the age of this machine.
    Peace,
    Clarke
    rangerdj's Avatar
    rangerdj Posts: 1, Reputation: 1
    New Member
    		  
    #8

    Jul 8, 2011, 03:45 PM
    I am having the same issue. Did you find a solution??
    DG's Avatar
    DG Posts: 1,375, Reputation: 109
    Ultra Member
    		  
    #9

    Jul 10, 2011, 07:34 AM

    Hi rangerdj , how old is the tractor your asking about ?
    DG
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

We have a John Deere 4010 that doesn't start [ 2 Answers ]

We have a John Deere 4010 that doesn't start. We used to use it all the time. Since my dad died a few years ago we haven't been using it much, but we usually start it every 2-3 months and drive it around a little. In November, for the first time, it wouldn't start. The starter makes a whirring...

Tenant won't pay rent, won't move furniture out and won't answer calls from me! [ 4 Answers ]

I have a tenant who won't pay rent, won't move furniture out and won't take calls from me. They do not use the house as a primary residence. They are very wealthy and definitely have the means to pay. Just incredibly evasive and dismissive. Dotn know where to turn. Someone please help! I cannot...

Garage door opener lights won't come on? [ 3 Answers ]

I have an alliance genie garage door opener ( Model # 600), which holds two light bulbs, when operating the garage door up and down niether light bulb will come on. I removed the exterior housing from the unit and checked all wiring connections everything seems to be OK? What do I look for next?

John Deer rider won't restart [ 1 Answers ]

My L110 John Deer rider won't restart after either trying to start it or after it's been running. It takes about an Hour for it to tries to start again.

John deer sabre won't start [ 1 Answers ]

I have a john deer sabre model 1438 gear. There is a wire that comes from a fuse that I do not know were it goes. I hooked it directly to the posative on the battery and I blow my fuse. I hook it to the selenoid were the powere wire connects from the battery and the fuse blows. I hook it to the...

View more questions Search