Ask Experts Questions for FREE Help !
Ask
    dtate's Avatar
    dtate Posts: 2, Reputation: 1
    New Member
    		  
    #1

    Feb 22, 2010, 01:52 PM
    Thermostat power transformer
    Can I connect a thermostate directly to a 24 volt transformer plugged into a wall outlet rather than taking the power from the furnace (LP fireplace in this case)? My existing thermostat runs on battery power alone and I do not see a transformer in the fireplace unit. WOuld be much simpler for me to connect to a transformer plugged into a wall outlet
    letmetellu's Avatar
    letmetellu Posts: 3,151, Reputation: 317
    Ultra Member
    		  
    #2

    Feb 22, 2010, 02:38 PM

    If you do not have a transformer at the fireplace you must have a 120 volt gas valve. Therefore all you would need to make a thermostat work is two wires going to the thermostat, but it would have to be a 120 volt thermostat unless you used a relay to turn on the gas valve.

    It is possible that you have a milivolt system?

    If this in not what you were wanting to know send me more information.
    dtate's Avatar
    dtate Posts: 2, Reputation: 1
    New Member
    		  
    #3

    Feb 22, 2010, 03:15 PM
    Thank you for taking the time to chat with me. SItuation is I have an LP fireplace that is currently controlled by a battery operated thermostat. I want to replace the thermostat with a Venstar thermostat (for RF control from phone). My existing thermostat has all 6 wires from the unit giong into to sources (R and W or WH I believe). Works like a charm - ignites the fires when needed and turns it off when not. Just no power to the wall thermostat. ANy thoughts would be appreciated and THANKS AGAIN. THe set up I purchased may not work.
    letmetellu's Avatar
    letmetellu Posts: 3,151, Reputation: 317
    Ultra Member
    		  
    #4

    Feb 22, 2010, 06:35 PM

    I still don't understand if you have a transformer or not. If not what power turn the gas valve on. Also what in the new thermostat would have to have 24 volts of power to make it work. My thinking is that you should be able to make the thermostat switch from on to off and back with nothing connected to the thermostat.

    It is hard to reason without knowing just what you have.
    KISS's Avatar
    KISS Posts: 12,510, Reputation: 839
    Uber Member
    		  
    #5

    Feb 22, 2010, 07:06 PM

    OK. Let me try.

    Fireplaces are typically a millivolt system and thus two terminals.
    This means that you need an isolated contact and a low EMF contact. Preferably one that's silver.

    The Idec RM2S-UL-AC24V relay would work fine.

    http://www.remelectronics.com/Search...cturerAbbr=IDC

    R & C go to the secondary of the transformer. W and C go to the new relay. The NO (Normally Open) contacts go where the existing thermostat was.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

How is a transformer connected to get power and then give power to the thermostat [ 2 Answers ]

This is about hvac units: how is a transformer connected to get power and then give power to the thermostat And where is the transformer excactly - lets say on a residential a/c unit with gas furnace

Questions on a power transformer [ 38 Answers ]

Hey Folks, I have a 36-volt Lestronic II battery charger that is not working. I do have a slight background in electronics so I've done the diagnosis which resulted in some questions. Here is the situation. When I plug it in (120 volts AC) and turn it on, the transformer draws 8.9 amps...

Wiring power transformer to furnace [ 4 Answers ]

I have a lennox furnace & I am trying to replace my transformer. On my old transformer one side has a black wire coming out connecting to a black wire coming out of the furnace. On the same side there is a white wire connecting to a yellow wire on furnace. On the other side there is a red wire...

View more questions Search