Ask Experts Questions for FREE Help !
Ask
    edwood2001's Avatar
    edwood2001 Posts: 3, Reputation: 1
    New Member
    		  
    #1

    Feb 6, 2010, 08:56 AM
    AFCI requirements for panel upgrade in New Jersey
    Do I need to install arc fault breakers when I upgrade a panel or service in a residential dwelling in New Jersey ?
    The 2008 NEC is unclear to me on this matter.
    tkrussell's Avatar
    tkrussell Posts: 9,659, Reputation: 725
    Uber Member
    		  
    #2

    Feb 6, 2010, 11:14 AM
    The Code is not retroactive. If your only changing the service, and not doing any re-wiring in the home, none of the existing circuits need to be AFCI protected. The local inspector may suggest if at all possible, but he/she should not require it.
    donf's Avatar
    donf Posts: 5,679, Reputation: 582
    Printers & Electronics Expert
    		  
    #3

    Feb 6, 2010, 11:41 AM
    However if you are adding circuits, then yes you need AFCI protection on the new circuits.
    edwood2001's Avatar
    edwood2001 Posts: 3, Reputation: 1
    New Member
    		  
    #4

    Feb 6, 2010, 12:43 PM
    Thank you both for the answers. This is what I thought.
    Different township inspectors are giving me contradictory answers on this.
    Just want to be sure to avoid any red stickers on inspections and additional
    Costs for the AFCI breakers.
    LandserElectric's Avatar
    LandserElectric Posts: 15, Reputation: 3
    New Member
    		  
    #5

    Feb 9, 2010, 08:48 PM

    When I was coming up every time I asked a question like that the answer was "call the inspector". Inspectors are people, they get egos and pet peeves... and for all you know might play golf with the mayor or at least the chief inspector. I don't know if you've ever heard "you can't fight city hall", but trust me, its true. Remember, inspectors are often the ones that couldn't make it in the trade and they have the power. They may read the code different than you. Call the guy up and ask him, because if the guy the next county over or next cubicle says one thing, it doesn't matter. The guy who signs the card will be the answer. You don't want a pissing match over it, you might have the same guy again.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Can I upgrade my panel to 200amp from 100amp [ 3 Answers ]

My utility company feeders are 1/0 aluminum... can I upgrade from 100amp panel to 200 amp panel with the existing feeders or do I need to call them?

Panel upgrade [ 3 Answers ]

I have an outside meter without an outside panel my wire come through my wall and to a lug fed inside panel. There is no room in this panel and I am putting a bigger box in there what size copper wire do I need for a 200 amp service and will I have to go to a main fed panel. Also with it being the...

Service Panel Upgrade [ 3 Answers ]

I have a permit and authorization to upgrade to a 200 Amp Service Panel. There may be a need to extend the house wires in the service panel to reach the new breakers. What is a approved connection/connector to extend existing black wiers in the panel?

Service panel upgrade [ 3 Answers ]

I have a 1200 sf 1958 Florida home with an older fuse panel located inside a bedroom closet, serving the entire home, including the kitchen oven, range, water heater, etc. I also have a circuit breaker equipted panel, located outside the home, immediately beside the meter, serviing the AC unit, Air...

Service panel upgrade [ 2 Answers ]

What is entailed in changing the service box from 100 amp service to 150 or 200 amp service. Can a layman do this on his own?

View more questions Search